Aiwa ADC-M60 User Manual

Size:
1.71 Mb
Download

dlri’m

DIGITAL AUDIO

ADC-M60Y”

COMPACT DISC CHANGER CAMBIADOR DE DISCOS COMPACTOS

OWNER’S RECORD

For your convenience, record the model number and serial number (you will find them on the rear of your set) in the space provided below. Please refer to them when you contact your AIWA dealer in case of difficulty.

Model No. [ ADC-M60

‘eria’ ‘0 ~

Welcome

Thank you for your purchasing this AIWA product. To optimize the performance of this unit, please read through this manual carefully.

TABLE OF CONTENTS

~FEATURES

Tracks from 6 CDs stored in the disc magazine can be selected and played.

Horizontal, vertical, slanted or suspended installation can be made.

Through the window at the top of the unit, you can see a disc spinning as it plays.

Since it IS smaller in size, you will find it easier to install the unit.

1 E/UGL/SH

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These Iimlts are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there ISno guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can ba determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/ TV technician for help.

CAUTION

Modifications oradjustmentsto this product, which are not expressly approved by the manufacturer, may void the user’s right or authority to operate this product.

PRECAUTIONS

Do NOT install the unit in a location where it may be subjected to:

— Direct sunlight or other sources of excessive heat

— Fluid, rain or moisture

— Excessive dirt or dust

— Excessive vibration

This unit is designed to be operated on a 12-voitDCnegative-groundelectrical system only.

Choose the mounting location carefully so that the unit will not interfere with normal driving functions.

Before making connections, disconnect the ~ terminal of the car battery to avoid short circuiting.

Notes on CDs

A defective or soiled disc stored in the disc magazine can cause the sound to drop out during play.

Always handle a disc by holding its inner and outer edges.

Do NOT touch the surface of the unlabeled side of the disc.

Do NOT attach paper or tape etc. to a disc.

Do NOT expose the discs to direct sunlight or excessive heat.

Clean the discs before inserting them into the disc magazine. Always clean a disc from the center outward with a cleaning cloth.

/.

\\

There may be burrs left on the inner and outer edges of a brand-newdisc. The burr may cause the malfunction of the unit or sound dropout. To prevent these problems, if the burr is left on the disc, be sure to remove them with aball-pointpen, etc. as illustrated.

&Ball-pointpenf Burr

Burr

@

Ball-pointpan

%

NEVER usesolventssuch as benzineoralcohol to clean a disc.

You cannot play an 8-cm(3-inch)CD — even with the specially designed adaptor.

Do NOT use irregular shape CDs (example: heart-shaped,octagonal ones).

It may result in malfunction.

Notes on the disc magazine

Do NOT leave the disc magazine in a place subject to excessive temperature or humidity.

Do NOT insert more than one disc per slot.

Do NOT drop the disc magazine.

ENGLISH 2

~UNPACKING

Compact disc changer

Compact disc magazine

Connecting cable

Supplied mounting kit

for the compact disc changer

The letters are keyed to those in the instructions.

Use only the supplied mounting hardware for safe and secure installation.

@ Brackets (1 pair)

@ Washer screws

@ Plate brackets

@ Nuts (4 ea.)

 

(4 ea.)

(2 ea.)

 

 

 

 

e

 

 

B

@

 

 

‘=.O e

 

w)

 

 

 

-.

 

 

 

/

 

@ Adhesive label

 

 

 

(1 sheet)

 

 

 

Gig

 

 

 

o

 

 

 

~ENGLISH

INSTALLATIONS

Precautions

Select the mounting location very carefully, referring to the following points.

Make sure that there is no fuel tank, wiring or piping on the other side of the mounting surface.

Make sure that the installation of the unit will not hinder the movement of the deck lid or interfere with the spare tire, etc.

Use only the supplied mounting kit for safe and proper installation.

Mounting angle setting levers

Be sure to change the position of both mounting angle setting levers according to the angle at which the unit is to be installed.

Mounting angla setting levers

Removing the transport screws

Find the three transport screws at the bottom of the unit, which lock the unit’s mechanism during transport. Remove these screws before installation.

Retain these screws and replace them in the original positions if the unit is transported for service or maintenance.

Insert a pointed object such as a screw driver or ball-pointpen, etc. into the low spot of the lever and slide the lever to the position from among HORIZONTAL, 45°, and VERTICAL positions.

Notes

Be sure to eject the disc magazine when you set the levers.

Be sure to set both levers to the same position.

Be sure to set the levers exactly at the position (notch). If the lever is deviate from the position, the sound may drop out.

. Care must be taken when you mount the unit at the angle of lower than level. The diet magazine may drop if you eject the magazine.

Do NOT turn over the unit or slide the lever when the unit is activated. Doing so may damage the mechanism or the discs in the unit.

. The mounting angle setting levers on each side of the unit are factory-setto the HORIZONTAL position.

When you complete the setting, attach the supplied adhesive labels @ over the slots.

ENGLISH 4

h INSTALLATIONS

Horizontal installation

Construction

For details on @@@..., see page 3.

Note

If the mounting surface needs to be strengthened, secure the plate brackets @to the bottom surface of the car trunk, etc. with the tapping screws (not supplied).

The effective angle of the unit.

The position of the lever.

2

3

Deciding the position

Removing temporarily

4

5

Making holes in the carpet

Completion

Vertical installation

Construction

1

For details on @@@..., see page 3.

Note

If the mounting surface needs to restrengthened, secure the plate brackets @ to the bottom surface of,the car trunk, etc. with the tapping screws (not supplied).

2 Deciding the position

plate @if it

n9.

If installation space is narrow, bend the plate bracket

@back and forth along the perforated line to break off the end.

4 Making holes in the carpet

3 Removing temporarily5 Completion

ENGLISH 6

~ INSTALLATIONS

Suspended installation

When installing the unit in the trunk below the package tray, observe the following.

Select the mounting location carefully so that the unit does not hinder the movement of the torsion bars of the deck lid.

Caution

Before drilling the holes, make sure that there is nothing on the other side of the mounting surface.

Construction

1

For details on @@@..., see page 3.

The effective angle of the unit.

\’“d:-=.

 

-

 

0

The position of the lever.

 

 

!“@@

 

 

‘n

 

 

 

 

 

1

 

\

@Jw

-’

4!3 H-L

 

 

YF

 

FIN

 

 

 

 

 

 

 

 

 

2 Making holes

 

 

 

 

3 Completion

 

Tepping screws are not supplied

Slanted installation

 

 

 

 

Note on the brackets@

 

Be

sure to

set

the

To save

installation

space, you can place the

15“

mounting

angle

brackets

@ inside

out, as illustrated below.

15“

setting levers

to

the

 

 

 

45”A.

45°

position.

 

 

 

 

 

.

 

 

 

 

 

 

7 ENGLISH

~CONNECTIONS

This unit is designed only for AIWA brand car

stereo. Therefore you can not use the unit with

other brand’s equipment.

+

 

 

 

 

to AIWA brandrcar stereo

 

 

 

Caution

 

 

 

Note

Be sure to disconnect

the ground

wire terminal

of

Use only the supplied connecting cable. Using an

the car battery before

making

a connection

in

unspecified connecting cable may cause background

 

noise.

order to prevent short circuiting.

ENGLISH 8

,HOW TO USE

How to use a compact disc magazine

1.

With the label side up, insert a disc all the way

*&

6 discs, one in

each disc tray t

Recorded side

2

Open the

3 A

INSERT

Dlac magazine

Insert the magazme (which has tIeen taken out of the unit) fv’mly wkh the .4A mark visible on the top side.

4

a

To remove a disc, pull part@ in the direction of the arrow aa illustrated.

A (eject) button

To remove the magazine, press the ~ button and Pull out the disc magazme.

Close