Aiwa ADC M55YU User Manual [en, es, fr]

0 (0)

OPERATING INSTRUCTIONS MANUAL DE INSTRUCCIONES MODE D’EMPLOI

COMPACT
DIGITAL AUDIO
ADC-M55

COMPACT DISC CHANGER CAMBIADOR DE DISCOS COMPACTOS

YU
ENGLISH
FRANÇAIS

OWNER’S RECORD

For your convenience, record the model number
and serial number (you will find them on the rear of your set) in the space provided below. Please refer to them when you contact your AIWA dealer in case of difficulty.
Model No. IADC-M55 Serial No. f
Welcome
Thank you for your purchasing this AIWA product. To optimize the performance of this unit, please read through this manual carefully.
TABLE OF CONTENTS
FEATURES.....................................................................................................................................................1
PRECAUTIONS..............................................................................................................................................2
UNPACKING...................................................................................................................................................3
INSTALLATIONS............................................................................................................................................4
CONNECTIONS .............................................................................................................................................8
HOW TO USE.................................................................................................................................................9
SPECIFICATIONS.........................................................................................................................................10
FEATURES
• Tracks from 6 CDs stored in the disc magazine can be seiected and piayed.
' Horizontal, vertical, slanted or suspended
installation can be made

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules, These
limits are designed to provide reasonabie protection against harmfui interference in a residentiai instaiiation.
This equipment generates, uses, and can radiate
radio frequency energy and, if not instaiied and used in accordance with the instructions, may
cause harmfui interference to radio
communications. However, there is no guarantee
that interference wiil not occur in a particuiar
instaiiation. If this equipment does cause harmfui
interference to radio ortelevision reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the foilowing measures:
1 ENGLISH
— Reorient or reiocate the receiving antenna. — Increase the separation between the
equipment and receiver.
— Connect the equipment into an outlet on
circuit different from that to which the receiver
IS connected.
— Consult the dealer or an experienced radio/
TV technician for heip,

CAUTION

Modifications or adjustments to this product, which are not expressiy approved by the manufacturer, may void the user’s right or authority to operate this product.
PRECAUTIONS
• Do NOT install the unit in a location where it may be subjected to: — Direct sunlight or other sources of excessive
heat — Fluid, rain or moisture — Excessive dirt or dust — Excessive vibration
• This unit is designed to be operated on a 12-volt DC negative-ground electrical system only.
• Choose the mounting location carefully so that the unit will not interfere with normal driving functions.
• Before making connections, disconnect the 0 terminal of the car battery to avoid short circuiting.

Notes on CDs

• A defective or soiied disc stored in the disc magazine can cause the sound to drop out during piay.
• Always handle a disc by holding its inner and outer edges.
' Do NOT touch the surface of the unlabeled side
of the disc. Do NOT attach paper or tape etc. to a disc.
' Clean the discs before inserting them into the
disc magazine. Always clean a disc from the center outward with a cleaning cloth.
• There may be burrs left on the inner and outer edges of a brand-new disc. The burr may cause the malfunction of the unit or sound drop out. To prevent these problems, if the burr left on the disc, be sure to remove them with a ball point pen, etc. as illustrated.
Bail-point pen
Burr
Bail-point pen
m
z
o r
w
X
• Do NOT expose the discs to direct sunlight or excessive heat.
• NEVER use solvents such as benzine or alcohol to clean a disc.
• You cannot play an 8-cm (3-inch) CD — even with the specially designed adaptor.
• Do not use irregular shape CDs (example:
heart-shaped, octagonal ones).
It may result in malfunction.

Notes on the disc magazine

• Do NOT leave the disc magazine in a place subject to excessive temperature or humidity.
• Do NOT insert more than one disc per slot.
• Do NOT drop the disc magazine.
ENGLISH 2
■ UNPACKING

Compact disc changer Compact disc magazine Connecting cable

Supplied mounting kit

for the compact disc changer The letters are keyed to those in the instructions.
Use only the supplied mounting hardware for safe and secure installation.
® Bra'ckets (2 ea.)
"o'
® Double-back tape
(large) (2 sets)
® Adhesive label
(1 seet)
® Washer screws
(4 ea.)
® Lead clamp
(1 ea.)
© Plate brackets @ Wing nuts (4 ea.)
® Lead clamp
(2 ea.)
3 ENGLISH
INSTALLATIONS

Precautions

Select the mounting location very carefuily, referring to the following points.
• Make sure that there is no fuel tank, wiring or piping on the other side of the mounting surface.
• Make sure that the instaliation of the unitwill not hinder the movement of the deck iid or interfere with the spare tire, etc.
• Use only the supplied mounting kit for safe and proper instaliation.

Removing the transport screws

Find the three transport screws at the bottom of
the unit, which lock the unit's mechanism during transport. Remove these screws before installation. Retain these screws and replace them in the originai positions if the unit is transported for service or maintenance.

Mounting angie setting ievers

Be sure to change the position of both mounting angle setting ievers according to the angie at which the unit is to be installed.
Mounting angle setting levers
Insert a pointed object such as a screw driver or ball-point pen, etc. Into the low spot of the lever and slide the lever to the position from among H (horizontal), 45°, and V (vertical) positions.
Notes
• Be sure to eject the disc magazine when you set the
levers.
• Be sure to set both levers to the same position.
• Be sure to set the levers exactry at the position (notch). If the lever is deviate from the position, the sound may drop out.
• Care must be taken when you mount the unit at the angle of lowerthan level. The disc magazine may drop If you eject the magazine.
• Do NOT turn over the unit or slide the lever when the unit is activated. Doing so may damage the mechanism or the discs in the unit.
• The mounting angle setting levers on each side of the unit are factory-set to the H (horizontal) position.
• When you complete the setting, attach the supplied adhesive labels (D over the slots.
ENGLISH 4
INSTALLATIONS
Horizontal installation
with the tapping screws (not suppiied).
2 Deciding the position
^ Making hoies in the carpet

Vertical installation

Construction
1
For details on ®®®-, see page 3.
of the car trunk, etc. with the tapping screws (not supplied).
’ if instaliation space is narrow, bend the piate bracket © back and
forth aiong the perforated line to break off the end.
2 Deciding the position Making holes in the carpet
2 Removing temporarily
INSTALLATIONS

Suspended installation

When installing the unit in the trunk below the package tray, observe the following.
• Select the mounting location carefully so that the unit does not hinder the movement of the
torsion bars of the deck lid.

Construction

1
For details on ®®©..., see page 3.

Caution

Before drilling the holes, make sure that there is nothing on the other side of the mounting surface.

2 Making holes

Sianted installation
/15^X^ \ setting levers to the
45/
7 ENGLISH
Be sure to set the mounting angle
45° position.

2 Completion

Tapping screws are not supplied.
CONNECTIONS
This unit is designed oniy for AiWA brand car stereo. Therefore you can not use the unit with other brand’s equipment.

Caution

Be sure to disconnect the ground wire terminal of the car battery before making a connection in order to prevent short circuiting.
Note
• Use only the supplied connecting cable. Using an unspecified connecting cable may cause background noise.

Secured with the lead clamp ©

After connection, secure the cable in place with the lead clamp © and a lead clamp (h) or electrical tape (not supplied).
■ HOW TO USE

How to use a compact disc magazine

1
With the label side down, insert a CD all the way.
Bottom of the magazine
Recorded side
Labeled side
INSERT
Insert the magazine (which has been taken out of the unit) firmly with the A, mark visible on the top side.
To remove a CD, pull part ® in the direction of the arrow as illustrated.
To remove the magazine, press the ± button
and pull out the disc magazine.
9 ENGLISH
Loading...
+ 23 hidden pages