Aiwa ADC-EXI06 User Manual

Size:
1.76 Mb
Download

m!r

IGITAL AUDIO

~

ADC-EXI06YU

COMPACT DISC CHANGER CAMBIADOR DE DISCOS COMPACTOS

.

B“

OWNER’S RECORD

For your convenience, record the model number and serial number (you will find them on the rear of your set) in the space provided below. Please refer to them when you contact your AIWA dealer in case of difficulty.

Model No. I ADC-EX106

‘eria’ ‘0 ~

Welcome

Thank you foryourpurchasmg this AIWAproduct. Tooptimize theperformance ofthisunit, please read through this manual carefully.

TABLE OF CONTENTS

~FEATURES

Tracks from 10 CDs stored in the disc magazine can be selected and played.

Horizontal, vertical, slanted or suspended

installation can be made.

The EASS (ElectronicAnti-ShockSystem) function reduces skipping or muting of the sound when the unit is subjected to a shock.

This unit continues to play with just a short break when changing discs, using playback sound data transferred to its memory.

This function works only when discs are changed in order.

CD text information can be displayed in the display window of the car stereo.

This function may not be available, depending on the specifications of the car stereo.

Through thewindow atthetop of the unit, you can see a disc spinning as it plays.

Since it issmaller in size, you will find it easier to install the unit.

1 ENGLISH

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on circuit different from that to which the recewer is connected.

Consult the dealer or an experienced radio/ TV technician for help.

CAUTION

Modifications oradjustmentsto this product, which are not expressly approved by the manufacturer, may void the user’s right or authority to operate this product.

PRECAUTIONS

Do NOT install the unit in a location where it may be subjected to:

— Direct sunlight or other sources of excessive heat

— Fluid, rain or moisture

— Excessive dirt or dust

— Excessive vibration

This unit is designed to be operated on a 12-voltDCnegative-groundelectrical system only.

Choose the mounting location carefully so that the unit will not interfere with normal driving functions.

Before making connections, disconnect the @ terminal of the car battery to avoid short circuiting.

Notes on CDs

A defective or soiled d!sc stored in the disc magazine can cause the sound to drop out during play.

Always handle a disc by holding its Inner and outer edges.

Clean the discs before inserting them into the disc magazine. Always clean a disc from the center outward with a cleaning cloth.

There may be burrs left on the inner and outer edges of a brand-newdisc. The burr may cause the malfunction of the unit or sound dropout. To prevent these problems, if the burr is left on the disc, be sure to remove them with aball-pointpen, etc. as illustrated.

Ball-pointpen

Burr

Do NOT touch the surface of the unlabeled side of the disc.

Do NOT attach paper or tape etc. to a disc.

Do NOT expose the discs to direct sunlight or excessive heat.

Burr @

Ball-pointpen

%

NEVER usesolventssuch as benzineoralcohol to clean a disc.

You cannot play an 8-cm(3-inch)CD — even with the specially designed adaptor.

Do NOT use irregular shape CDs (example: heart-shaped,octagonal ones).

It may result in malfunction.

Notes on the disc magazine

Do NOT leave the disc magazine in a place subject to excessive temperature or humidity.

Do NOT insert more than one disc per slot.

Do NOT drop the disc magazine.

ENGLISH 2

UNPACKING

Compact disc changer

Compact disc magazine

Connecting cable

Supplied mounting kit

for the compact disc changer

The letters are keyed to those in the instructions.

Use only the supplied mounting hardware for safe and secure installation.

@ Brackets (1 pair)

@ Washer screws

@ Plate brackets

@ Nuts (4 ea.)

 

(4 ea.)

(2 ea.)

 

@Adhesive label (1 sheet)

3 ENGLISH

INSTALLATIONS

Precautions

Select the mounting location very carefully, referring to the following points.

Make sure that there is no fuel tank, wiring or piping on the other side of the mounting surface.

Make sure that the installation of the unit will not hinder the movement of the deck lid or interfere with the spare tire, etc.

Use only the supplied mounting kit for safe and proper installation.

Mounting angle setting levers

Be sure to change the position of both mounting angle setting levers according to the angle at which the unit is to be installed.

Mounti~g angle setting levers

Removing the transpotl screws

Find the three transport screws at the bottom of theunit, which lockthe unit’smechanism during transport. Remove these screws before installation.

Retain these screws and replace them in the original positions if the unit is transported for service or maintenance.

 

45’

45

Q

 

RIZONTAL

 

HORIZONTAL

n

‘if

0

 

 

 

“g

Insert a ~ointed obiect such as a screw driver or ball-point pen,etc.-intothe low spot of the lever and slide the lever to the position from among HORIZONTAL, 45°, and VERTICAL positions.

Notes

. Be sure to eject the disc magazine when you set the levers.

Be sure to set both levers to the same position.

Be sure to set the levers exactly at the position (notch). If the lever is deviate from the position, the sound may drop out.

Care must be taken when you mount the unit at the angle of lower than level. The disc magazine may drop if you eject the magazine.

Do NOT turn over the unit or slide the lever when the unit is activated. Doing so maydamagethe mechanism or the discs in the unit.

The mounting angle setting levers on each side of the unit are factory-setto the HORIZONTAL position.

When you complete the setilng, attach the supplied adhesive labels @ over the slots.

i

do

~

,,.-,0

 

/

,,, ,,.,

@

I

;,” ,

 

 

: ,,/

 

.,

ENGLISH 4

~ INSTALLATIONS

Horizontal installation

Construction

1

For details on @@@..., see page 3.

Note

If the mounting surface needs to be strengthened, secure the plate brackets @to the bottom surfece of the car trunk, etc. with the tapping screws (not supplied).

2 Deciding the position

Removing temporarily

The effective angle of the unit.

The position of the lever.

450 ,n

HORIZONTAL

r

4 Making holes in the carpet

/’”/

v

~Completion

5 ENGLISH

Vertical installation

Construction

1

For details on @@@..., see page 3.

Notes

If the mounting surface needs to be strengthened, secure the plate brackets @ to the bottom surface of the car trunk, etc. with the tapping screws (not suppliad).

2 Deciding the position

3 Removing temporarily

The

effective angle of

The

position of

the

unit,

Ithe

lever.

. If installation space is narrow, bend the plate bracket ~eb:;:and forth along the perforated line to break off

Making holes in the carpet

Completion

ENGLISH 6

~ INSTALLATIONS

Suspended installation

When installing the unit in the trunk below the package tray, observe the following.

Select the mounting location carefully so that the unit does not hinder the movement of the torsion bars of the deck lid.

Construction

1

For details on @@@..., see page 3.

2 Making holes

Slanted installation

15“

15“

A45”

“. . a.

Be sure to setthe mounting angle setting levers to the 45° position.

.

Caution

Before drilling the holes, make sure that there is nothing on the other side of the mounting surface.

9

The effective angle of the unit.

(f”4!3 u

HORIZONTAL

3 Completion

Tapping screwe are not supplied.

Note on the brackets@

To save installation space, you can place the brackets @ inside out, as illustrated below.

7 ENGLISH

CONNECTIONS

This unit is designed only for AIWA brand car stereo. Therefore you cannot use the unit with other brand’s equipment.

Compact disc changsr

Caution

Be sure to disconnect the ground wire terminal of the car battery before making a connection in order to prevent shorl circuiting.

to AIWA brand car stereo

Note

Use only the supplied connecting cable. Using an unspecified connecting cable may cause background noise.

ENGLISH 8

HOW TO USE

How to use a compact disc magazine

With the label side up, inserl a disc all the way.

10 discs, one in

7

each disc tray

Recorded side

 

2

Open the d

3

&

INSERT

Disc magazine

Insert the magazine (which has been taken

out of the unit) firmly with the LA mark visible on the top side.

Close

To remove a disc, pull part@ in the direction of the arrow as illustrated.

A (eject) button

To remove the magazine, press the A button and pull out the disc magazine.

9 ENGLtSH