Aiphone AC-10F, AC-10S User Manual

FK1376 A YS0108

AC-10S, AC-10F

Access Control

Clavier à Codes rétro-éclairé

Türcodemodul

Control de acceso

Codeklavier

Surface mount type Clavier saillie Aufputztyp

Montaje en superficie Opbouwmontage

AC-10S

Flush mount type Clavier encastré Unterputztyp Montaje empotrado Inbouwmontage

AC-10F

INSTALLATION & OPERATION MANUAL NOTICE D'INSTALLATION ET D'UTILISATION INSTALLATIONSUND BEDIENUNGSANLEITUNG MANUAL DE INSTALACIÓN Y USO INSTALLATIE & GEBRUIKSHANDLEIDING

RECORD OF SETTINGS AND REGISTRATION DETAILS (Please make sure to write down your settings below.) AIDE MEMOIRE DES PROGRAMMATIONS ENREGISTREES (Faire en sorte de bien noter vos réglages ci-dessous.) VERZEICHNIS DER EINSTELLUNGEN UND REGISTRIERUNGSDETAILS (Bitte notieren Sie unten Ihre Einstellungen.) DATOS DE CONFIGURACIÓN Y DETALLES DE LOS REGISTROS (Asegúrese de apuntar los valores de ajuste abajo.) LIJST MET GEPROGRAMMEERDE INSTELLINGEN EN CODES (Zorg ervoor uw instellingen hieronder op te schrijven.)

Master code
Code maître
Mastercode
Código maestro
Hoofdcode
Key illumination time
Temporisation d'éclairage
Tastenbeleuchtungszeit
Tiempo de encendido de las teclas
Verlichtingsduur klavier		sec/sek/seg
Relay output time	Relay 1
Temporisation des relais	Relais 1
Relais Ausgabezeit	Relais 1
Tiempo de salida Relé	Relé 1
Relais outputtijd	Relais 1	sec/sek/seg
	Relay 2
	Relais 2
	Relais 2
	Relé 2
	Relais 2	sec/sek/seg

External output setting
Paramétrage de sortie externe	ON		OFF
Externer Ausgang
Ajuste de la salida externa	EIN		AUS
Activering Alarmuitgang	AAN		UIT
Lockout
Blocage	ON		OFF
Eingabe-Sperre
Bloqueo	EIN		AUS
Blokkering klavier	AAN		UIT
Auto-relock
Auto-reverrouillage	ON		OFF
Automatische Neuverriegelung
Re-bloqueo automático	EIN		AUS
Automatische hersluiting	AAN		UIT
Timer-linked unlocking
Déverrouillage lié à l'horloge
Timergesteuerte Entriegelung	1	2	1&2
Desbloqueo conectado al temporizador
Tijdsgebonden ontgrendeling
Operation tone
Bip de fonctionnement	ON		OFF
Signaltöne
Tono de operación	EIN		AUS
Zoemer klavier	AAN		UIT

Registered User Code List / Liste des codes utilisateur programmés / Liste der registrierten Zugangscodes Lista de códigos de los usuarios registrados / Lijst Codes Geregistreerde Gebruikers

	group 1 / groupe 1 / gruppe 1 / grupo 1 / groep 1																group 2 / groupe 2 / gruppe 2 / grupo 2 / groep 2
00								30								60								90
01								31								61								91
02								32								62								92
03								33								63								93
04								34								64								94
05								35								65								95
06								36								66								96
07								37								67								97
08								38								68								98
09								39								69								99
10								40								70
11								41								71
12								42								72
13								43								73
14								44								74
15								45								75
16								46								76
17								47								77
18								48								78
19								49								79
20								50								80
21								51								81
22								52								82
23								53								83
24								54								84
25								55								85
26								56								86
27								57								87
28								58								88
29								59								89

1

English

PRECAUTIONS

General Prohibitions Prohibition to Dismantle the Unit General Precautions

WARNING

(Negligence could result in death or serious injury to

people)

1. Do not connect any non-specified power source to the V, V terminals, and do not install two power supplies in parallel to a single input. Fire, damage to the unit, or system malfunction could result.

2. The unit is not explosion-proof. Do not install or use near gases or flammable materials. Fire or explosion could result.

3. Do not dismantle or alter the unit. Fire or electric shock could result.

4. Do not allow the wires or DC output terminals to be shorted. Fire or electric shock could result.

CAUTION

(Negligence could result in injury to people or damage

to property)

1. When mounting the unit on a wall, install the unit in a convenient location, but not where it could be jarred or bumped. Injury could result.

2. Do not install or make any wire terminations while power supply is plugged in. It can cause electrical shock or damage to the unit.

3. Before turning on power, make sure wires are not crossed or shorted. Fire or electric shock could result.

4. Do not install the unit in any of the following locations. Fire, electric shock, or unit trouble could result.

*Places subject to dust, oil, chemicals, hydrogen sulfide (hot spring).

*Places subject to moisture and humidity extremes, such as bathroom, cellar, greenhouse, etc.

*Places where the temperature is quite low, such as inside a refrigerated area or in front of air-conditioner.

*Places subject to steam or smoke (near heating or cooking surfaces).

*Where noise generating devices such as dimmer switches, invertor electrical appliances, are closeby.

GENERAL PRECAUTIONS

1.This product, being a control unit of door release, should not be used as a crime-prevention device.

2.This product is weather-resistant, but do not spray high-pressure water on it. Unit trouble could result.

3.The product becomes inoperative during power failure.

4.As to other manufacturer's devices, such as sensor, door releases, timer, used with this system, comply with the Specifications and Warranty conditions manufacturers or venders present.

CONTENTS

RECORD OF SETTINGS AND REGISTRATION DETAILS … 1	FUNCTIONS SETTING UP ……………………………… 5
PRECAUTIONS …………………………………………… 2	OPERATIONS ……………………………………………… 9
PACKAGE CONTENTS …………………………………… 2	TECHNICAL PRECAUTIONS …………………………… 9
NAMES ……………………………………………………… 3	SPECIFICATIONS ………………………………………… 9
MOUNTING ………………………………………………… 3	WARRANTY ………………………………………………… 9
MOUNTING/WIRING METHOD, WIRING DISTANCE …… 4	TEMPLATE FOR AC-10S MOUNTING BRACKET (SCALE 1:1) … 42

PACKAGE CONTENTS

AC-10S

AC-10F

Unit

Mounting

Mounting

Special

Operation

Unit

Flush mount

Special

Operation

bracket

screws

screwdriver

manual

back box

screwdriver

manual

Nederlands Español Deutsch Français English

2

Nederlands Español Deutsch Français English

NAMES

12

	4
1	2
3	3
	4
4

1 LED indicator (Orange)

2 LED indicator (Green)

3 Keys (Yellow)

4 Special screws for panel mounting

MOUNTING

AC-10S

1.Drill holes in the wall to match the size and number of screws.

2.Attach the mounting bracket to the wall using the mounting screws.

3.Attach the unit to the mounting bracket using the special screwdriver and the special screw for mounting.

AC-10S
	55mm (2-3/16")
Cable	1
Spare screw holes	Wall
	3
	Click
	2

AC-10F

1.Detach the AC-10F panel using the special screwdriver supplied.

2.Attach the flush mount back box to the wall.

3.Attach the panel to the flush mount back box using the special screwdriver and the special screws for panel mounting.

AC-10F	85mm (3-3/8")
	100mm
	(3-15/16")
	45mm
	(1-12/16")
	Flush mount back box

When this unit is to be used with the JF-DV, please refer to the illustration below when installing it.

Please also refer to "TEMPLATE FOR AC-10S MOUNTING BRACKET(SCALE 1:1)"(page 42).

1. JF-DV unit	2. Positions for drilling holes
	Please refer to the
	illustration below when
	drilling the holes. Make
	sure the cable inlet is within
	the shaded area shown in
	the illustration below.

173mm (6-13/16")
98mm (3-7/8")	42.5mm	2/3")-(1

55mm

(23/16")-

3

49mm 49mm (1-15/16") (1-15/16")

A hole for cable inlet

3. Position of mounting bracket	4. Installation
Refer to the illustration	Attach the unit to the mounting bracket
below when attaching the	by pushing it into the bracket. Tighten
mounting bracket.	the screws to complete the installation.

	98mm (3-7/8")
	(7/16")
3.5mm	11.5mm
(1/8")

49mm (1-15/16")

15mm(9/16")	55mm
	64mm (2-1/2")

() As there are drain holes at the bottom of the JF-DV unit, do not block the space

between the JF-DV and the access control keypad.

42.5mm(12/3")-		5mm (3/16")
(2-3/16")	68.5mm(2-11/16")	( )

Cable inlet

MOUNTING/WIRING METHOD, WIRING DISTANCE

	D		A		(Wiring distance)
				Power supply
						Power supply	diameter 0.65 - 1.0 mm (22-18AWG)
	Relay
						AC/DC12 ~ 18V	100m (330')
					A
						(Less than)
		2
			2			AC/DC18 ~ 24V	300m (980')
	Automatic gate		B		B	-	300m (980')
				Request to exit/entry	C	-	300m (980')
			2			The connection distance will depend on
	Relay			button
			2			the specifications of the electric door strike,
	2
or				Request to exit/entry	D	relays or Electromagnetic door lock to be
				button		connected. To determine the operating range,
						please refer to the specifications of each
Electromagnetic	Electric		2	Timer		terminal.
door lock	door strike

C

Deutsch Français English

Terminal names

Back view of AC-10S

User group1 relay 1

User group2 relay 2

Power supply

Request to

Request to

N/C contact

N/C contact

exit/entry

exit/entry

Common

Timer

button 1

button 2

C

T

NO1

NC1

C2

NC2

V

V

PB1

PB2

C1

NO2

N/O contact

N/O contact

Power supply

Request to exit/entry button Timer

Relay

Between 12 and 24V AC

Minimum overload :100mV DC, 0.1mA or above

24V DC, 3A (resistive load) 1A (inductive load)

Between 12 and 24V DC

Contact capacity: 3V DC, 0.1A or above

24V AC, 3A (resistive load) 1A (inductive load)

Minimum overload :5V DC, 100mA or above

Connection of Relay 1 only

Example of electric door

Example of automatic

Example of electromagnetic door

strike connection

(N/O)

gate connection (N/O)

lock connection (N/C)

V

V

PB1

PB2

C

T

NO1

C1

NC1

NO2

C2

NC2

NO1

C1

NC1

N

NO1

C1

NC1

NO2 C2

Electric door strike

Electromagnetic

2

door lock

NP

2

NP

2

NP

2

2

or

or

NP

NP

Request to exit/entry button

Automatic gate

Power supply

AC transformer

Power supply

(push button, etc.)

Relay 1: Automatic gate (N/O contact), Relay 2: Electric door strike (N/O contact)

V

V

PB1

PB2

C

T

NO1

C1

NC1

NO2

C2

NC2

2

External output

NP

2

2

NO2

C2

Power supply

NP

NP

Only connecting to the terminal

Rating

of relay 2 is possible.

Between 12 and 24V AC

Alarm, Security

Between 12 and 24V DC

For relay 1

Electric door strike

Request to

2

Automatic gate

exit/entry button

NP

For relay 2

AC transformer

Request to

2

exit/entry button

NP

Auto-relock/External out put by forced entry

N.C

(sensor connection is required)

To set VJG "auto-relock" / "External output by forced entry" function a

Timer

2

PB2

C

sensor (locally avallable) is required.

The request to exit/entry button for relay 2 cannot be used when the

NP

"auto-relock" / "External out put by forced entry" function are set.

4

Nederlands Español

Nederlands Español Deutsch Français English

FUNCTIONSSETTING UP

This section explains the settings of each function, including the master code for management, the user code for unlocking, the buzzer and the LEDs.

About the setting mode:

Enter master code twice to switch to the setting mode, and enter the following setting code to perform the settings for the desired function. After settings have been made, enter the following setting codes to continue the setting operation. Press to exit the setting mode.

	Setting items		Allowable setting range	Default value	Setting code
Setting the code length			4, 5, or 6 digits	4 digits
Change the length of the master code and the user code.
)They both must be the same length.
Setting the master code			1	1234
Enter a master code using between 4 and 6 digits (alpha or numeric) to			Valid keys: 0 - 9, A, B
switch to the setting mode.
) The number of digits in the code can be set by setting the code length.
Setting the code for user group 1			Number of codes: 60	-	-
Set the unlocking code for user group 1.			Valid keys: 0 - 9, A, B
) The number of digits in the code can be set by setting the code length.
Setting the code for user group 2			Number of codes: 40	-	-
Set the unlocking code for user group 2.			Valid keys: 0 - 9, A, B
) The number of digits in the code can be set by setting the code length.
Setting the key illumination time			Illumination time: 10 to 99	10 Sec.
Set the length of time that the keys will be lit up after they are pressed.			seconds, or continually lit
Setting the relay 1 output time			Output time: 1 to 99	3 Sec.
Set the output time of relay 1.			seconds, or latched
Setting the relay 2 output time			Output time: 1 to 99	3 Sec.
Set the output time of relay 2.			seconds, or latched
Reset Settings			-	-
Return all the settings to their default values.
External output setting			· OFF	OFF
The alarm or security system connected to the terminal of relay 2 will be			· During Lockout
activated when the "Lockout" * or the forced entry* is carried out.			· During forced entry output
* "Lockout": Refer to VIII below. *Forced entry: This function is linked with			· During lockout and forced
the door open/close sensor (N.C.) which is connected to PB2 and C, and			entry output
carried out when opening the door without activating this unit. (For example,
entry in an improper manner, manual unlock, etc.)
) If there is a way to open the door without activating this unit, such as
manual unlock, do not make the external output setting for the forced entry.
Lockout			ON/OFF	OFF
If several incorrect access codes are attempted, the code input function is			Invalid number of times:
disabled for a programmed period of time.			10 to 99 times
· When "Lockout" is activated, the LED (Orange) indicator and the keypad			Invalid time:
blink, and the buzzer sounds for 3 seconds. This is just a sound to inform			10 to 99 seconds
you that the function has been activated. It is not a warning sound. If you
want a warning to be sounded, please use the external output function to
activate a commercially-available alarm device.
· The unlock function will work when the request to exit/entry button is
pushed, even while the "Lockout" function is operating.
Auto-relock (Anti-tailgate)			ON/OFF	OFF
After the door has been linked to the door open/close sensor (N/C), and
unlocked, it will relock itself one second after being closed, thus preventing
the entry of an unauthorized third party. )1
Timer-linked unlocking setting			Linked relay: relay 1	Linked relay: relay 1
The system can be set to unlock the door by pressing the		key within	relay 2	0 key illumination: OFF
the set time and linking it to the external timer (N/O). The operations for the			relay 1 and 2
LEDs and the buzzer after unlocking are the same as those used to perform			0 key illumination: ON/OFF
user code unlocking. When the door is linked to the timer, unlocking can be
performed using the user code and the request to exit/entry button. When
latch output is performed for the relay settings, the relay turns ON/OFF
every time the	key is pressed.
Operation tone settings			ON/OFF	ON

Set the tone heard when the keypad is being used to ON/OFF.

•The setting can be saved even when the power is off.

•The system cannot be switched to the setting mode while the relay is unlocked.

•When the setting mode has been activated and no operations are performed for approximately 120 seconds, the system will exit the setting mode. (If a key is pressed during that time, the timer will start over.)

•Neither the request to exit/entry button nor the timer-linked unlocking key can be operated, and unlocking using the user code cannot be performed while the setting mode is activated.

•The volume (the check tone, operation tone, etc.) from the main unit may become lower according to the mounting status.

5	1	: When the auto-relock is used, the request to exit/entry button for relay 2 cannot be used. The output of relay 2 is
		only possible when user code unlocking is performed.

Orange (L)	The result of each operation is indicated by the
	Green (R)
	lighting up of the LED indicators on the upper section
	of the unit, and by the sounding of the buzzer.

	(orange)	(green)
Input the master code twice.	Illumination Blinking
(Default:	)	Bleep, Bleep

Setting the code length	Setting the master code			Setting the code
(Default: 4 digits)	(Default	1234)	group 1		group 2
			00 - 59		60 - 99
Input the setting code.	Input the setting code.		Inputting of user number (ex.: 01)		Inputting of user number (ex.: 60)
				When a user code		When a user code
				that has already		that has already
Illumination Blinking	Illumination	Blinking		been set is selected		been set is selected
Bleep		Bleep		Blinks		Blinks
			Illumination Blinking Illumination twice		Illumination Blinking Illumination twice
			Bleep	Bleep,	Bleep	Bleep,
				Bleep		Bleep

	Inputting of code length (ex.: 5 digits)	Inputting of new master code	Inputting of code (ex.: 1006)	Inputting of code (ex.: 04B2)
	4, 5, or 6 digits	(ex.: 4321)	* Numbers 0 - 9 and the	* Numbers 0 - 9 and the
			letters A and B can be used	letters A and B can be used
	Illumination Blinking	Illumination Blinking	Illumination Blinking	Illumination Blinking
	Beep	Beep
			Beep	Beep

- When the			key is pressed, the green LED lights up, the buzzer beeps twice, and the system exits the setting mode.	Indicator	Blinking
				goes out
(If the		key is included in the user code and the master code, the system does not exit the setting mode.)
									Bleep,
- You can continue the setting up operation by entering an arbitrary setting code.									Bleep

·The set code will be saved in memory, even if the code length is changed. However, codes of different lengths cannot be used.

·When the code length has been changed, the master code returns to the default value (if the number of digits in the code is 4, 5, or 6, the master code is 1234, 12345, or 123456 respectively).

·Please note that the shift to the setting mode can be performed

during timer-linked unlocking.

However, if "" is included in the master code, the door will

be unlocked, and the shift to the setting mode will not be able to be performed.

·The same code cannot be set for both the user code and the master code (the previously set code has priority).

·Do not set simple codes, such as 1111.

·We recommend that you change the default master code.

·To make the set user code invalid, press 0000 (when 4 digits are used), 00000 (when 5 digits are used), or 000000 (when 6 digits are used). Code numbers which contain only "0" cannot be set as user codes.

·As the factory pre-setting master code is 1234, 1234 (when 4 digits are used), 12345 (when 5 digits are used), and 123456 (when 6 digits are used) cannot be set as user codes.

·Do not set simple codes, such as 1111.

*The same code cannot be set for both the user code and the master code. The previously set code has priority.

6

Nederlands Español Deutsch Français English

Nederlands Español Deutsch Français English

		(orange) (green)
Input the master code twice.		Illumination Blinking
(Default :	)	Bleep, Bleep

	Setting the key illumination time	Setting the relay output time		Reset Settings	External output setting
	(Default: 10 Sec.)	(Default: 3 Sec.)			(Default: OFF)
		When setting relay 1	When setting relay 2
	Input the setting code.	Input the setting code.	Input the setting code.	Input the setting code.	Input the setting code.
	Illumination Blinking	Illumination	Blinking	Illumination Blinking	Illumination Blinking
	Bleep		Bleep	Bleep	Bleep

During	During forced	During lockout	OFF
		and forced
Lockout	entry output	entry output

Inputting of illumination time	Inputting of relay output time
(ex.: 20 seconds)	(ex.: 99 seconds)
10 - 99	01 - 99
Indicator is lit up at all times: 00	Latched ( ) : 00
Illumination Blinking	Illumination Blinks three times	Illumination Blinking
	Illumination Blinking	Beep
Beep	Bleep, Bleep, Beep
	Beep

- When the			key is pressed, the green LED lights up, the buzzer beeps twice, and the system exits the setting mode.	Indicator	Blinking
				goes out
(If the		key is included in the user code and the master code, the system does not exit the setting mode.)
									Bleep,
- You can continue the setting up operation by entering an arbitrary setting code.									Bleep

·( ) If the latched status has been set and the door is unlocked, it will not be locked again until the user code is entered (or the request to

exit/entry button is pressed, or the key is pressed while timer-linked unlocking is set).

·When the door is unlocked during relay outputting (including when latched), the system cannot be switched to the setting mode.

· If the power is turned off and the , , and keys are

pressed simultaneously while the unlock 1 input status is active (short circuit between terminals PB1 and C), the settings can be returned to their default values by turning the power back on and pressing the , , and

keys simultaneously for 3 seconds.

·When setting the external output, do not set the relay 2 output to be latched.

7

(orange) (green)

Illumination Blinking

Input the master code twice.

(Default : ) Bleep, Bleep

	Lockout		Auto-relock		Timer-linked unlocking setting				Operation sound settings
			(Anti-tailgate)
	(Default: OFF)				(Default: relay 1, OFF)				(Default: ON)
			(Default: OFF)
	Input the setting code.		Input the setting code.		Input the setting code.				Input the setting code.
	Illumination	Blinking	Illumination	Blinking	Illumination Blinking				Illumination	Blinking
		Bleep		Bleep				Bleep		Bleep
	OFF	ON	OFF	ON	Relays 1 and 2	Only relay 1		Only relay 2	Operation	Operation
					are both linked	is linked		is linked	tone OFF	tone ON
	Illumination Blinking	Illumination Blinking	Illumination Blinking		Illumination		Blinking		Illumination Blinking
				Beep				Bleep		Beep
	Beep	Bleep
					0 key illumination OFF		0 key illumination ON
					while timer is on		while timer is on
	Inputting the number of operations
	(ex.	10 times)
	10 -99
	Illumination Blinking				Illumination		Blinking
		Bleep						Beep

Inputtinglengthoftimein"Lockout"mode (Ex.: 10 seconds)

10 - 99

Illumination Blinking

Beep

- When the			key is pressed, the green LED lights up, the buzzer beeps twice, and the system exits the setting mode.	Indicator	Blinking
				goes out
(If the		key is included in the user code and the master code, the system does not exit the setting mode.)
									Bleep,
- You can continue the setting up operation by entering an arbitrary setting code.									Bleep

·When the relay 1 output time is set to latched output, the auto-relock function is disabled.

·When the auto-relock function is turned on, the unlock function of the request to exit/entry button of relay 2 is disabled.

·If the 0 key illumination function is turned on while the timer is on, only the 0 key illumination will light up, even if the "key illumination time setting" is set to "Indicator is continually lit".

Nederlands Español Deutsch Français English

8