AEG-Electrolux 1400D-M User Manual

0 (0)

1400 D

Dunstabzugshaube

Afzuigkap

Hotte aspirante

Cooker Hood

Montageund Gebrauchsanweisung Installatieen gebruksaanwijzing Manuel de montage et d’utilisation Operating and Installation Instructions

Printed on recycled paper

AEG - putting words into action

55

Contents

Safety warnings

57

for user

 

for kitchen unit installer

 

Introduction

59

Extractor version

 

Filter version

 

Hood operation

60

Maintenance and care

61

Metal grease filter

 

Carbon filter

 

Changing the light bulb

 

Cleaning

 

Special accessories

 

Technical assistance service

 

Guarantee conditions

 

Service

 

Technic Details

67

Installation

68

Electrical connection

 

Wall unit mounting

 

Wall mounting

 

 

 

 

 

56

Safety warnings

for user

Always cover lighted elements, to prevent excess heat from damaging the appliance. In the case of oil, gas and coal fired cookers it is essential to avoid open flames.

Also, when frying, keep the deep frying pan on the cooker top/ cooker under careful control.

The hot oil in the frying pan might ignite due to overheating.

The risk of self-ignition increases when the oil being used is dirty.

It is extremely important to note that overheating can cause a fire.

Never carry out any flambé cooking under the hood.

Always disconnect the unit from the power supply before carrying out any work on the hood, including replacing the light bulb (take the cartridge fuse out of the fuse holder or switch off the automatic circuit breaker).

It is very important to clean the hood and replace the filter at the recommended intervals. Failure to do so could cause grease deposits to build up, causing a fire hazard.

for kitchen unit installer

When used as an extractor unit, the hood must be fitted with a 120mm diameter hose.

If the fumes must be forced out through the wall, you must obtain a MKZ sizable wall exhaust pipe (with external exhaust and air intake), E-Nr.- 610 899 004 (Ø 120 mm) which is one of our optional parts.

When installing the hood, make sure you respect the following minimum distance from the top edge of the cooking hob/ ring surfaces:

electric cookers

600 mm

gas cookers

650 mm

coal and oil cookers

700 mm min.

57

The national decree on fuel-burning systems specifies a maximum depression of 0.04 bar in such rooms.

The air outlet must not be connected to chimney flues or combustion gas ducts. The air outlet must under no circumstances be connected to ventilation ducts for rooms in which fuel-burning appliances are installed.

It is advisable to apply for authorization from the relevant controlling authority when connecting the outlet to an unused chimney flue or combustion gas duct.

The air outlet installation must comply with the regulations laid down by the relevant authorities.

When the unit is used in its extractor version, a sufficiently large ventilation hole must be provided, with dimensions that are approximately the same as the outlet hole.

National and regional building regulations impose a number of restrictions on using hoods and fuel-burning appliances connected to a chimney, such as coal or oil room-heaters and gas fires, in the same room.

Hoods can only be used safely with appliances connected to a chimney if the room and/or flat (air/environment combination) is ventilated from outside using a suitable ventilation hole approximately 500-600 cm2 large to avoid the possibility of a depression being created during operation of the hood.

If you have any doubts, contact the relevant controlling authority or building inspector’s office.

Since the rule for rooms with fuel burning appliances is “outlet hole of the same size as the ventilation hole”, a hole of 500-600 cm2, which is to say a larger hole, could reduce the performance of the extractor hood.

If the hood is used in its filtering function, it will operate simply and safely in the above conditions without the need for any of the aforementioned measures.

When the hood is used in its extractor function, the following rules must be followed to obtain optimal operation:

short and straight outlet hose

keep bends in outlet hose to a minimum

never install the hoses with an acute angle, they must

always follow a gentle curve only

— keep the hose as large as possible (120 mm Ø min.).

Failure to observe these basic rules will drastically reduce the performance and increase the noise levels of the extractor hood.

58

AEG-Electrolux 1400D-M User Manual

Introduction

Extractor version

lThe hood is supplied as an extractor unit and can also be used with a filtering function by fitting one activated carbon filter (special accessory).

lYou will need original AEG activated carbon filter for this function (see Special Accessories).

lThe unit features two outlet holes, one of which A is located on the top of the unit while the other B is located on the rear.

lTo connect up the hose, you should first fit the bayonet-mounting flange C (Ø 120 mm) on the outlet required (if using the top outlet, fix the flange in place using the screw supplied as shown in Fig. 1). Close off the unused hole using the bayonet fitting caps D.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 1

 

Fig. 2

lWarning! If is decided to use the rear outlet hole B, first remove the sponge E that closes that hole. Fig. 2.

Filter Version

l The air is filtered and recirculated through the front grid. l Move the lever G to position F -

Fig. 3.

● You will need an original AEG KF14 activated carbon filter for the filtering function. (See Special Accessories).

Fig. 3

59

Loading...
+ 13 hidden pages