ADTRAN 61175044L2-22B User Manual

Size:
212.44 Kb
Download

AC/DC POWER

SUPPLY AND BATTERY CHARGER

P/N: 1175043L1

CLEI: SIMPAAAARA

P/N: 1175043L2

CLEI: SIMPAADARA

P/N: 1175043L3

CLEI: SIMPAAEARA

Note: The AC/DC Power Supply and Battery Charger is designed for use with the Total Access 750 and 850. It is not used with the Total Access 612/616/624 units.

C A U T I O N !

SUBJECT TO ELECTROSTATIC DAMAGE

OR DECREASE IN RELIABILITY.

HANDLING PRECAUTIONS REQUIRED.

JOBAID

AC/DC POWER SUPPLY AND BATTERY CHARGER

PRICING AN D AVAILA BILITY

800

.827.0887

RETURN FO R R EPAIR

256

.963.8722

 

TECHNICAL SUPPOR T

888

.4ADTRAN

 

61175044L2-22B

 

MOUNTING INSTRUCTIONS

1

Remove the Total Access 750/850 AC/DC Power Supply

(ADTRAN P/N 1175043Lx) from the box and inspect for

 

damage. If damage is apparent, contact your carrier or

 

supplier.

2 Place the power supply with the power cord oriented downward.

3 Use four #6 x 3/8" machine screws (supplied) to mount the power supply to either side of the Total Access 750/850 shelf.

Note: Threaded mounting holes are provided on both sides of the shelf.

Note: For battery backup installations, it is recommended to mount the power supply on the left side of the Total Access 750/850 shelf, next to the battery cover hinge.

Note: Alternatively, the power supply can be mounted to the backboard with four #6 x 1" wood screws (not supplied).

STATUS LEDS

AC Power Operation (AC power only)

Battery Operation (AC power supply or battery backup)

GREEN

OK

GREEN

OK (charging)

YELLOW

Power Fail

YELLOW

Discharging

RED

Power Fail

RED

Low (<-40V)

OFF

Power Fail

OFF

Disconnected

RELAYS

Alarm Relay

Provided for customer use

Condition

Alarm Relay

 

 

Normal

Open

 

 

AC Power Failure/

Cycles open/closed once per second if AC voltage <88 Vrms at full load and battery

Battery Backup engaged

backup is connected

 

 

Battery voltage <-45V

Stays closed if voltage <-45VDC to indicate that battery is becoming depleted

 

 

Battery Disconnect Relay

Disconnects battery pack from the system if the battery voltage falls below -40VDC

Prevents damage to batteries

CIRCUIT BREAKER

The device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by ADTRAN could void the user's authority to operate this equipment.

WARRANTY

Warranty for Carrier Network products manufactured by ADTRAN and supplied under Buyer's order for use in the U.S. is ten (10) years. For a complete copy of ADTRAN's U.S. Carrier Networks Equipment Warranty: (877) 457-5007,Document 414.

3- amp circuit breaker

Protects unit from over - current

Rocker button extends out from front panel when tripped

Reset by pushing in on the rocker button

GROUNDING

An 18 AWG or larger ground wire is required to connect additional ground connector to "ground bus" in customer equipment room.

ELECTRICAL SPECIFICATIONS

TELECOMMUNICATIONS CODES

AC input: 115 V nominal

 

 

 

 

 

Code

Input

Output

 

Range: 90 to 132 VAC

 

 

 

 

 

 

PC

F

C

DC output: -54V, 60 W average, 100 W peak

 

 

 

 

 

 

TC

Battery charging: 16 hr nominal, 24 hr maximum

 

 

 

 

E

 

 

 

IC

Battery discharge: Up to 8 hours

JOBAid, 61175044L2-22B,December 2002

Technical Support 1-888-4ADTRAN(1-888-423-8726)

Copyright 2002 ADTRAN, All Rights Reserved

BATTERY

BACKUP

UNIT

P/N: 1175044L2

CLEI: SIMPBBBARA

Note: Battery Backup Unit is designed for use with the Total Access 612, 616, 624, 750 and 850 units.

C A U T I O N !

SUBJECT TO ELECTROSTATIC DAMAGE

OR DECREASE IN RELIABILITY.

HANDLING PRECAUTIONS REQUIRED.

BATTERY BACKUP UNIT

JOBAID

61175044L2-22B

 

 

MOUNTING INSTRUCTIONS

BATTERY SPECIFICATIONS

 

1

Unpack the Total Access 750/ 850 Battery Backup Unit and inspect

for damage. If damage is apparent, refer to your carrier or supplier

 

for remedy.

 

 

 

 

 

Note: It is not necessary to remove the batteries during

 

installation process.

 

 

2

The battery box must be mounted with the following minimum

clearances:

 

 

 

 

 

Top-9"(for Total Access 750/850)

 

Top- 5" (for Total Access 612/616/624)

 

Left Side-5"

 

 

 

Right Side-1”

 

 

 

Bottom-3"

 

 

 

 

3

Using the template provided, mark and drill three pilot holes for #10

mounting screws.

 

 

4

Insert #10 x 3/ 4" flathead wood screws (supplied) into the three

pilot holes, leaving 1/ 16" space between the screwhead and the

 

backboard.

 

 

 

 

 

CAUTION: Fully loaded Battery box weighs 30 lbs.

5

Mount the battery box on the three support screws on the backboard.

6

cover.Remove the two closure screws on the battery box and open the

7

Use a long shaft screwdriver to tighten the three support screws.

 

WARRANTY

 

 

 

 

 

Warranty for Carrier Network products manufactured by ADTRAN and

 

supplied under Buyer's order for use in the U. S. is ten (10) years, except

 

for batteries which carry manufacturer's warranty. For a complete copy of

 

ADTRAN's U. S. Carrier Network Equipment

 

Warranty: (877) 4575007, Document 414.

 

TELECOMMUNICATIONS CODES

 

 

 

 

 

 

 

 

Code

 

Input

 

Output

 

 

 

 

 

 

 

 

 

IC

 

 

C

 

 

 

 

 

 

 

 

 

TC

 

 

 

 

 

 

 

 

 

 

 

PC

 

E

 

 

 

 

 

 

 

 

 

MAINTENANCE

Batteries: 7 Amp/ hr (4 batteries per pack)

Case size: 6" W x 3 3/ 4" H x 2 1/ 2" D

Battery type: Lead acid

Voltage: -54VDC

Backup Time: Up to 8 hours

Wire Gauge: 18 AWG

Preferred Temperature: 68º F (20º C)

The device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by ADTRAN could void the user's authority to operate this equipment.

1175044L2 BATTERY BACKUP

-48VDC

Note: The connection for the Total Access 850 will be identical to the Total Access 750.

CAUTION!

Total Access 750

 

 

 

 

 

 

 

 

 

 

During

V.35

 

 

 

 

 

Total Access 750

WARNING:

 

 

R1-I

LY IN

 

MUST BE REMOVED

 

 

 

 

20 Hz FUSE

T1

 

Terminal

P2

 

 

 

 

 

LX IN

 

 

 

 

 

access

 

wall installation,

BEFORE REMOVING COVER.

 

 

cover

 

 

FT1

 

T1-I

EU2

 

 

 

T-O

LY EU1

 

 

 

 

R-O

LX OUT

 

 

 

 

 

 

OUT

 

position the

 

 

 

 

MLT-A

 

 

 

 

 

-48ALM

 

 

MANAGEMENT

 

 

MLT-B

 

 

 

 

 

 

chassis so front

 

 

 

 

MJ

 

 

 

 

-48V

MJVR

 

 

 

 

 

-48R

MJR

 

 

 

 

DC

 

MJV

 

panels face up.

 

 

POWER

 

 

 

 

 

 

 

 

 

 

-54VDC Output to

 

 

 

 

 

Total Access 750

 

 

 

 

 

 

 

 

To Alarms

 

 

 

AC/DC Power Supply

120VAC/

-54VDC

AC ALARM

 

 

 

 

BATTERY

 

 

 

 

2A 60HZ INPUT OUTPUT

 

 

 

 

Battery Charging Unit

 

INPUT

OUTPUT

 

 

 

 

 

 

 

 

 

P/N: 1175043Lx

GROUND

+ -

 

1175044L2

 

 

AC Power Input

 

 

-54VDC Battery

 

 

 

 

 

 

 

 

BATTERY BACKUP

 

 

 

 

 

 

 

 

 

 

 

Charging/Discharging Line

 

 

 

 

 

CAUTION

During wall installation, position the Total Access 612/616/624 as shown in 61200624L1-19A.

-48VDC

9902271

Life expectancy: 3- 5 years on standby use

Battery performance is adversely affected by extreme emperatures.

Old barreries should be recycled. Reference60000120-36Afor

Total Access 612/616/624

further information.

AC Power Input

JOBAid, 61175044L2-22B,December 2002

Technical Support 1-888-4ADTRAN(1-888-423-8726)

Copyright 2002 ADTRAN, All Rights Reserved