ADTRAN 606 User Manual
Size:
5.01 Mb
Download

TOTAL ACCESS 600 SERIES

System Manual

Total Access 600R

Total Access 604

Total Access 608

Total Access 612

Total Access 616

Total Access 624

61200624L1-1BJune 2004

Trademarks

Total Access 600 Series System Manual

 

 

Trademarks

Any brand names and product names included in this manual are trademarks, registered trademarks, or trade names of their respective holders.

Total Access® is a registered trademark of ADTRAN, Inc.

To the Holder of the Manual

The contents of this manual are current as of the date of publication. ADTRAN reserves the right to change the contents without prior notice.

In no event will ADTRAN be liable for any special, incidental, or consequential damages or for commercial losses even if ADTRAN has been advised thereof as a result of issue of this publication.

About this Manual

This manual provides a complete description of the Total Access 6XX system and system software. The purpose of this manual is to provide the technician, system administrator, and manager with general and specific information related to the planning, installation, operation, and maintenance of the Total Access 6XX. This manual is arranged so that needed information can be quickly and easily found.

901 Explorer Boulevard

P.O. Box 140000

Huntsville, AL 35814-4000

Phone: (256) 963-8000

© 2004 ADTRAN, Inc.

All Rights Reserved.

Printed in U.S.A.

2

© 2004 ADTRAN, Inc.

61200624L1-1B

Total Access 600 Series System Manual Revision History

Revision History

Document Revision

Date

Description of Changes

 

 

 

 

 

 

A

October 2002

Initial Release

 

 

 

B

May 2004

Updated to include menu changes for firmware release.

 

 

 

Conventions

Notes provide additional useful information.

Cautions signify information that could prevent service interruption.

Warnings provide information that could prevent damage to the equipment or endangerment to human life.

61200624L1-1B

© 2004 ADTRAN, Inc.

3

Safety Instructions

Total Access 600 Series System Manual

 

 

Safety Instructions

When using your telephone equipment, please follow these basic safety precautions to reduce the risk of fire, electrical shock, or personal injury:

1.Do not use this product near water, such as a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.

2.Avoid using a telephone (other than a cordless-type)during an electrical storm. There is a remote risk of shock from lightning.

3.Do not use the telephone to report a gas leak in the vicinity of the leak.

4.Use only the power cord, power supply, and/or batteries indicated in the manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for special disposal instructions.

Save These Important Safety Instructions

4

© 2004 ADTRAN, Inc.

61200624L1-1B

Total Access 600 Series System Manual

FCC-RequiredInformation

 

 

FCC-RequiredInformation

FCC regulations require that the following information be provided in this manual:

1.This equipment complies with Part 68 of FCC rules and requirements adopted by ACTA. On the equipment housing is a label that contains, among other information, a product identifier in the format US: AAAEQ##TXXXX. If requested, provide this information to the telephone company.

2.If this equipment causes harm to the telephone network, the telephone company may temporarily discontinue service. If possible, advance notification is given; otherwise, notification is given as soon as possible. The telephone company will advise the customer of the right to file a complaint with the FCC.

3.The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the proper operation of this equipment. Advance notification and the opportunity to maintain uninterrupted service are given.

4.4.If experiencing difficulty with this equipment, please contact ADTRAN for repair and warranty information. The telephone company may require this equipment to be disconnected from the network until the problem is corrected or it is certain the equipment is not malfunctioning.

5.This unit contains no user-serviceableparts.

6.An FCC compliant telephone cord with a modular plug is provided with this equipment. This equipment is designed for connection to the telephone network or premises wiring using an FCC compatible modular jack, which is compliant with Part 68 and requirements adopted by ACTA.

7.The following information may be required when applying to your local telephone company for leased line facilities.

Product Listing

Registration Number

Service Type

REN/SOC

FIC

USOC

 

 

 

 

 

 

TA 600/604/608 Series

US:HDCDENAN4213680L1

1.544 Mbps - SF

 

04DU9-BN

 

T1 Products

 

 

 

1.544 Mbps - SF and B8ZS

6.0N

04DU9-DN

RJ-48C

 

 

TA 612/616/624 Series

US: HDCDENAN4213616L1

1.544 Mbps - ESF

04DU9-1KN

 

 

1.544 Mbps - ESF and B8ZS

 

04DU9-1SN

 

T1 Products

 

 

 

 

 

 

 

 

 

 

 

 

 

TA 600 Series

HDCUSA-44560-OT-N

Analog Loop Start/Ground Start

0.1B/9.0F

02LS2

RJ-11C

SDSL, SHDSL Products

02GS2

 

 

 

 

 

 

 

 

 

 

TA 600 Series

 

Analog Loop Start/Ground Start

0.1B/9.0F

02LS2

 

US:HDCDL02B4200644L1

02GS2

RJ-11C

 

 

ADSL Products

 

 

 

 

ADSL Service

0.2B/9.0F

02LS2

 

 

 

 

 

 

 

 

 

 

8.The REN is useful in determining the quantity of devices you may connect to your telephone line and still have all of those devices ring when your number is called. In most areas, the sum of the RENs of all devices should not exceed five. To be certain of the number of devices you may connect to your line as determined by the REN, call your telephone company to determine the maximum REN for your calling area.

9.This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs. Contact your state public utility commission or corporation commission for information.

61200624L1-1B

© 2004 ADTRAN, Inc.

5

FCC-RequiredInformation

Total Access 600 Series System Manual

 

 

Federal Communications Commission Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio frequencies. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Shielded cables must be used with this unit to ensure compliance with Class A FCC limits.

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

6

© 2004 ADTRAN, Inc.

61200624L1-1B

Total Access 600 Series System Manual

Affidavit Requirements for Connection to Digital Services

 

 

Affidavit Requirements for Connection to Digital Services

An affidavit is required to be given to the telephone company whenever digital terminal equipment without encoded analog content and billing protection is used to transmit digital signals containing encoded analog content which are intended for eventual conversion into voice band analog signal and transmitted on the network.

The affidavit shall affirm that either no encoded analog content or billing information is being transmitted or that the output of the device meets Part 68 encoded analog content or billing protection specifications.

End user/customer will be responsible to file an affidavit with the local exchange carrier when connecting unprotected CPE to a 1.544 Mbps or subrate digital service.

Until such time as subrate digital terminal equipment is registered for voice applications, the affidavit requirements for subrate services are waived.

61200624L1-1B

© 2004 ADTRAN, Inc.

7

Affidavit Requirements for Connection to Digital Services

Total Access 600 Series System Manual

 

 

AFFIDAVIT FORCONNECTION OFCUSTOMERPREMISESEQUIPMENT

TO 1.544 MBPS AND/ORSUBRATEDIGITALSERVICES

For the work to be performed in the certified territory of ___________________ (telco name) State of ________________

County of ________________

I, _______________________ (name), ____________________________________ (business address),

____________________ (telephone number) being duly sworn, state:

(

) I have responsibility for the operation and maintenance of the terminal equipment to be connected to 1.544 Mbps

 

and/or ________ subrate digital services. The terminal equipment to be connected complies with Part 68 of the

 

FCC rules except for the encoded analog content and billing protection specifications. With respect to encoded

 

analog content and billing protection:

(

) I attest that all operations associated with the establishment, maintenance, and adjustment of the digital CPE with

 

respect to analog content and encoded billing protection information continuously complies with Part 68 of the

 

FCC Rules and Regulations.

(

) The digital CPE does not transmit digital signals containing encoded analog content or billing information which

 

is intended to be decoded within the telecommunications network.

(

) The encoded analog content and billing protection is factory set and is not under the control of the customer.

I attest that the operator(s)/maintainer(s) of the digital CPE responsible for the establishment, maintenance, and adjustment of the encoded analog content and billing information has (have) been trained to perform these functions by successfully having completed one of the following (check appropriate blocks):

(

)

A. A training course provided by the manufacturer/grantee of the equipment used to encode analog signals;

 

 

 

or

(

)

B.

A training course provided by the customer or authorized representative, using training materials and

 

 

 

instructions provided by the manufacturer/grantee of the equipment used to encode analog signals; or

(

)

C.

An independent training course (e.g., trade school or technical institution) recognized by the

 

 

 

manufacturer/grantee of the equipment used to encode analog signals; or

(

)

D.

In lieu of the preceding training requirements, the operator(s)/maintainer(s) is (are) under the control of a

 

 

 

supervisor trained in accordance with _________ (circle one) above.

I agree to provide ______________________ (telco’s name) with proper documentation to demonstrate compliance with the information as provided in the preceding paragraph, if so requested.

_________________________________Signature

_________________________________Title

_________________________________ Date Transcribed and sworn to before me

This ________ day of _______________, _______

_________________________________

Notary Public

My commission expires:

_________________________________

8

© 2004 ADTRAN, Inc.

61200624L1-1B

Total Access 600 Series System Manual

Industry Canada Compliance Information

 

 

Industry Canada Compliance Information

The Industry Canada Certification label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The Department of Commerce does not guarantee the equipment will operate to the user's satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company's inside wiring associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic waterpipe system, if present, are connected together. This precaution may be particularly important in rural areas.

Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or an electrician, as appropriate.

The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the equipment that the total of the LNs of all devices does not exceed 100.

The ringer equivalence number (REN) assigned to each terminal adapter is used to determine the total number of devices that may be connected to each circuit. The sum of the RENs from all devices in the circuit should not exceed a total of 5.0.

Canadian Emissions Requirements

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causingequipment standard entitled “Digital Apparatus,”ICES-003of the Department of Communications.

Cet appareil numérique respecte les limites de bruits radioelectriques applicables aux appareils numériques de Class A prescrites dans la norme sur le materiel brouilleur: “Appareils Numériques,” NMB-003edictee par le ministre des Communications.

61200624L1-1B

© 2004 ADTRAN, Inc.

9

Product Warranty

Total Access 600 Series System Manual

 

 

Product Warranty

ADTRAN will repair and return this product within the warranty period if it does not meet its published specifications or fails while in service. Warranty information can be found at www.adtran.com/warranty.

Product Registration

Registering your product helps ensure complete customer satisfaction. Please take time to register your products on line at www.adtran.com. ClickService and Support on the top of the page, and then clickProduct Registration underSupport.

Customer Service, Product Support Information, and Training

ADTRAN will replace or repair this product within the warranty period if it does not meet its published specifications or fails while in service. Warranty information can be found at www.adtran.com/warranty.

A return material authorization (RMA) is required prior to returning equipment to ADTRAN. For service, RMA requests, training, or more information, use the contact information given below.

Repair and Return

If you determine that a repair is needed, please contact our Customer and Product Service (CAPS) department to have an RMA number issued. CAPS should also be contacted to obtain information regarding equipment currently in house or possible fees associated with repair.

CaPS Department

(256) 963-8722

Identify the RMA number clearly on the package (below address), and return to the following address:

ADTRAN Customer and Product Service

901 Explorer Blvd. (East Tower)

Huntsville, Alabama 35806

RMA # _____________

Pre-SalesInquiries and Applications Support

Your reseller should serve as the first point of contact for support. If additional pre-salessupport is needed, the ADTRAN Support web site provides a variety of support services such as a searchable knowledge base, latest product documentation, application briefs, case studies, and a link to submit a question to an Applications Engineer. All of this, and more, is available at:

http://support.adtran.com

When needed, further pre-salesassistance is available by calling our Applications Engineering Department.

Applications Engineering (800) 615-1176

10

© 2004 ADTRAN, Inc.

61200624L1-1B

Total Access 600 Series System Manual

Customer Service, Product Support Information, and Training

 

 

Post-SaleSupport

Your reseller should serve as the first point of contact for support. If additional support is needed, the ADTRAN Support web site provides a variety of support services such as a searchable knowledge base, updated firmware releases, latest product documentation, service request ticket generation and trouble-shootingtools. All of this, and more, is available at:

http://support.adtran.com

When needed, further post-salesassistance is available by calling our Technical Support Center. Please have your unit serial number available when you call.

Technical Support (888) 4ADTRAN

Installation and Maintenance Support

The ADTRAN Custom Extended Services (ACES) program offers multiple types and levels of installation and maintenance services which allow you to choose the kind of assistance you need. This support is available at:

http://www.adtran.com/aces

For questions, call the ACES Help Desk.

ACES Help Desk (888) 874-ACES(2237)

Training

The Enterprise Network (EN) Technical Training Department offers training on our most popular products. These courses include overviews on product features and functions while covering applications of ADTRAN's product lines. ADTRAN provides a variety of training options, including customized training and courses taught at our facilities or at your site. For more information about training, please contact your Territory Manager or the Enterprise Training Coordinator.

Training Phone

(800)

615-1176,ext. 7500

Training Fax

(256)

963-6700

Training Email

training@adtran.com

61200624L1-1B

© 2004 ADTRAN, Inc.

11

Customer Service, Product Support Information, and Training Total Access 600 Series System Manual

12

© 2004 ADTRAN, Inc.

61200624L1-1B

Total Access 600 Series System Manual

Table of Contents

 

 

Table of Contents

Section 1 System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

This section provides an overview of the Total Access 600 Series system.

Section 2 Engineering Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

This section provides equipment dimensions, power requirements, front panel design, rear panel design, LEDs, and at-a-glance specifications.

Section 3 Network Turnup Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

This section provides shipment contents list, grounding instructions, mounting options, and specifics of supplying power to the unit.

Section 4 User Interface Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

This section of ADTRAN’s Total Access 600 Series System Manual is designed for use by network administrators and others who will configure and provision the system. It contains information about navigating the VT100 user interface, configuration information, and menu descriptions.

Section 5 Detail Level Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183

DLP-1 Connecting a VT100 Terminal or PC to the CRAFT Port . . . . . . . . . . . . . . . . . . . . . 185 DLP-2 Logging in to the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 DLP-3 Setting IP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189 DLP-4 Verifying Communications Over an IP LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191 DLP-5 Connecting to the Unit Using Telnet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 DLP-6 Adding/Removing Users and Changing Password Security Levels . . . . . . . . . . . . . . 199 DLP-7 Updating the Firmware using TFTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203 DLP-8 Updating the Firmware using XMODEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207 DLP-9 Saving the Current Configuration Using TFTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209 DLP-10 Loading a Configuration Using TFTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211 DLP-11 Saving and Transferring a Current Configuration Using XMODEM. . . . . . . . . . . . . 213 DLP-12 Loading a Configuration Using XMODEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 DLP-13 Saving and Loading Text Configuration using Terminal Command Line . . . . . . . . . 217 DLP-14 A.03 to A.04 Firmware Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 DLP-15 Using the ADTRAN Utility Syslog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 DLP-16 Executing Terminal Mode Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 DLP-17 Configuring Dual T1 Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231 DLP-18 Unit Installation Using the Auto-Config Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235 DLP-19 TDM to ATM Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239

Section 6 ADTRAN Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243

This section provides instructions for configuring and using the ADTRAN Utilities software programs including Telnet, VT100, Syslog, and TFTP.

Section 7 MIBs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253

This section is divided into two parts: (1) SNMP information for TDM units and (2) SNMP information for ATM units. Each section details the Management Information Bases (MIBs) supported, MIB Compilation Order, Traps Supported, and MIB Variables supported.

61200624L1-1B

© 2004 ADTRAN, Inc.

13

Table of Contents

Total Access 600 Series System Manual

 

 

14

© 2004 ADTRAN, Inc.

61200624L1-1B