ADTRAN 203019L1 User Manual

Size:
240.4 Kb
Download

NT1 ACE

USER MANUAL

1203019L1: NT1 ACE with Power Supply 1203019L2: NT1 ACE

1203019L3: NT1 ACE International 336048VUR-2:Power Supply

61203019L1-1DJanuary 1999

FCC ID: HDC1203019L1

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Canadian Standards Association

This device must be powered by a CSA approved power supply or a power supply meeting the requirements of CS03, Part I Section 1.4.2.

Warranties

ADTRAN will repair or replace this product within five years from the date of shipment if it does not meet its published specifications or fails while in service. For detailed warranty, repair, and return information, refer to the ADTRAN Equipment Warranty and Repair and Return Policy Procedure. Return Material Authorization (RMA) is required prior to returning equipment to ADTRAN. (See inside back cover for phone and address.)

901 Explorer Blvd.

P. O. Box 140000

Huntsville, AL 35814-4000

Phone: (256) 963-8000

©1999 ADTRAN, Inc.

All rights reserved

Printed in USA

FCC regulations require that the following information be provided in this manual:

1.This equipment complies with Part 68 of the FCC rules. On the bottom of the equipment housing is a label that shows the FCC registration number for this equipment. If requested, provide this information to the telephone company.

2.If this equipment causes harm to the telephone network, the telephone company may temporarily discontinue service. If possible, advance notification is given; otherwise, notification is given as soon as possible. The telephone company will advise the customer of the right to file a complaint with the FCC.

3.The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the proper operation of this equipment; advance notification and the opportunity to maintain uninterrupted service is given.

4.If experiencing difficulty with this equipment, please contact ADTRAN for repair and warranty information. The telephone company may require this equipment to be disconnected from the net-

61203019L1-1

NT1 ACE User Manual

iii

work until the problem is corrected, or it is certain the equipment is not malfunctioning.

5.This unit contains no user-serviceableparts.

6.An FCC compliant telephone cord with a modular plug is provided with this equipment. In addition, an FCC compliant cable appropriate for the dial backup option ordered is provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using an FCC compatible modular jack, which is Part 68 compliant.

7.The following information may be required when applying to the local telephone company for leased line facilities.

Service

Digital Facility

Service

Network

Type

Interface Code

Order Code

Jacks

ISDN

02IS5

6.0N

RJ-49C

iv

NT1 ACE User Manual

61203019L1-1

ADTRAN YEAR 2000 (Y2K)

READINESS DISCLOSURE

ADTRAN has established a Year 2000 program to ensure that our products and operations will correctly function in the new millennium. ADTRAN warrants that all products meet Year 2000 specifications regardless or model or revision. Information about ADTRAN’s Year 2000 compliance program is available at the following:

Web Site

www.adtran.com

Product Matrix

www.adtran.com/Y2Kfax.html

Faxback Document Line

(256) 963-8200

 

Y2K plans and product certifications

 

are listed in the matrix

Y2K Project Line

(256) 963-2200

E-mail

year 2000@adtran.com

61203019L1-1

NT1 ACE User Manual

v

CANADIAN EMISSIONS REQUIREMENTS

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causingequipment standard entitled "Digital Apparatus,"ICES-003of the Department of Communications.

Cet appareil numerique respecte les limites de bruits radioelectriques applicables aux appareils numeriques de Class B prescrites dans la norme sur le materiel brouilleur: "Appareils Numeriques," NMB-003edictee par le ministre des Communications.

CANADIAN EQUIPMENT LIMITATIONS

Notice: The Canadian Industry and Science Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The Department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In

vi

NT1 ACE User Manual

61203019L1-1

some cases, the company’s inside wiring associated with a single-lineindividual service may be extended by means of a certified connector assembly (telephone extension cord). Compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or an electrician, as appropriate.

61203019L1-1

NT1 ACE User Manual

vii

The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the Load Numbers of all devices does not exceed 100.

viii

NT1 ACE User Manual

61203019L1-1

AFFIDAVIT REQUIREMENTS FOR CONNECTION

TO DIGITAL SERVICES

An affidavit is required to be given to the telephone company whenever digital terminal equipment without encoded analog content and billing protection is used to transmit digital signals containing encoded analog content which are intended for eventual conversion into voiceband analog signals and transmitted on the network.

The affidavit shall affirm that either no encoded analog content or billing information is being transmitted or that the output of the device meets Part 68 encoded analog content or billing protection specifications.

End user/customer will be responsible to file an affidavit with the local exchange carrier when connecting unprotected CPE to a 1.544 Mbps or subrate digital services.

Until such time as subrate digital terminal equipment is registered for voice applications, the affidavit requirement for subrate services is waived.

61203019L1-1

NT1 ACE User Manual

ix

AFFIDAVIT FOR CONNECTION OF CUSTOMER PREMISES EQUIPMENT TO 1.544 MBPS AND/OR SUBRATE DIGITAL SERVICES

For the work to be performed in the certified territory of _______________

(telco name)

State of __________________

County of ________________

I, ______________________________(name),

________________________(business address),

______________________ (telephone number) being duly sworn, state:

I have responsibility for the operation and maintenance of the terminal equipment to be connected to 1.544 Mbps and/or ________ subrate digital services. The terminal equipment to be connected complies with Part 68 of the FCC rules except for the encoded analog content and billing protection specifications. With respect to encoded analog content and billing protection:

( ) I attest that all operations associated with the establishment, maintenance, and adjustment of the digital CPEwith respecttoanalogcontentandencodedbilling protection information continuously complies with Part 68 of the FCC Rules and Regulations.

x

NT1 ACE User Manual

61203019L1-1