ADTRAN 1524ST Series User Manual

Size:
213.12 Kb
Download

®

 

For more detailed documentation, visit us online at www.adtran.com.

NetVanta 1524ST Series Switch

P/N 1200560E2/L2

 

Quick Start Guide

GETTINGSTARTED

Two configuration methods are available for your NetVanta switch:

Web-basedGUI

AOS Command Line Interface (CLI)

The GUI lets you configure the main unit settings and provides online guidance and explanations for each setting. However, using the AOS CLI may be necessary for more advanced configurations.

ACCESS THEGUI

You may access the web-basedGUI from any web browser on your network by following these steps:

1.Connect the switch to your PC using the ETH 0/0 port on the back of the unit.

2.Set your PC to obtain an IP address automatically (or if using the fixed IP address, set your PC to 10.10.20.2).

3.Enter the unit’s IP address in your browser address line. The default IP address is 10.10.20.1.

4.You will then be prompted for the username and password (the default settings are admin andpassword).

5.The initial GUI screen appears.

ACCESS THECLI

Access the AOS CLI via the CONSOLE port or a Telnet session. To establish a connection to the NetVanta switchCONSOLE port, you need the following items:

VT100 terminal or PC (with VT100 terminal emulation software)

Straight-throughserial cable with aDB-9(male) connector on one end and the appropriate interface for your terminal or PC communication port on the other end

1.Connect the DB-9(male) connector of your serial cable to theCONSOLE port on the rear panel of the unit.

2.Connect the other end of the serial cable to the terminal or PC.

3.Insert the connector of the provided power cord into the power interface on the rear panel of the unit, and plug the cord into a standard electrical outlet.

4.Once the unit is powered up, open a VT100 terminal session using the following settings: 9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press <Enter> to activate the AOS CLI.

5.Enter enable at the> prompt.

6.Enter the enable password when prompted. The default password is password.

The configuration parameters used in the examples outlined in this document are for instructional purposes only. Please replace all underlined entries (example) with your specific parameters to configure your application.

CONFIGURE THEUNITSIP ADDRESS

The following steps create an IP address and subnet mask for the virtual interface vlan 1. If you are not sure what IP address to assign, please contact your network administrator.

1.At the # prompt, enterconfig terminal.

2.At the (config)# prompt, enterinterface vlan 1 to access the configuration parameters for the virtual LAN (VLAN) interface.

3.Enter ip address 10.26.12.12 255.255.255.0 to assign an IP address to the VLAN interface using a24-bitsubnet mask.

4.Enter no shutdown to activate the virtual interface to pass data.

5.Enter exit to return to the Global Configuration mode.

Depending on your configuration, you may need to set a default gateway as well using the (config)#ip default gateway command.

ENABLETELNETACCESS

The following steps create a password of adtran for Telnet access. By default, Telnet access is enabled with a password ofpassword.

1.Verify that the prompt of your unit displays (config)#.

2.Enter line telnet 0 4 to change the configuration parameters for the Telnet sessions.

3.Enter login to initiate Telnet access.

4.Enter password adtran to change the login password for the Telnet sessions.

5.Enter exit to return to the Global Configuration mode.

6.Verify that the prompt of your unit displays (config)#.

7.Enter do write memory to save the current configuration.

Quick Start Guide, 61200560E1-13E,November 2006

Copyright © 2006 ADTRAN, All Rights Reserved

®

 

For more detailed documentation, visit us online at www.adtran.com.

NetVanta 1524ST Series Switch

P/N 1200560E2/L2

 

Quick Start Guide

ETHERNETPINOUTS

Pin

Name

Description

 

 

 

 

1

TR1+

Transmit/Receive 1 Positive

2

TR1-

Transmit/Receive 1

Negative

3

TR2+

Transmit/Receive 2

Positive

4

TR3+

Transmit/Receive 3

Positive

5TR3Transmit/Receive 3 Negative

6TR2Transmit/Receive 2 Negative

7

TR4+

Transmit/Receive 4

Positive

 

TR4-

Transmit/Receive 4

Negative

CONFIGUREYOURAPPLICATION

More detailed documentation for configuring your ADTRAN unit is provided on the ADTRAN OS System Documentation CD included in your shipment. For more detail on hardware setup, refer to the appropriate NIM Quick Start Guides and the Hardware Installation Guide. For more detail on configuring your system, refer to theADTRAN Operating System (AOS) Command Reference Guide, configuration guides, and technical support notes.

Important: For additional details on product features, specifications, installation, and safety, refer to the appropriate Hardware Installation Guide on theADTRAN OS System Documentation CD shipped with the base unit and available online at www.adtran.com.

CONSOLEPINOUTS

Pin

Name

Description

 

 

 

1

DCD

Data Carrier Detect (output)

2

RD

Receive Data (output)

3

TD

Transmit Data (input)

4

DTR

Data Terminal Ready (input)

5

SG

Signal Ground

6

DSR

Data Set Ready (output)

7

Unused

8

CTS

Clear to Send (output)

9

Unused

Quick Start Guide, 61200560E1-13E,November 2006

Copyright © 2006 ADTRAN, All Rights Reserved