ADTRAN 1355 PWR User Manual

Size:
234.47 Kb
Download

®

 

For more detailed documentation, visit us online at www.adtran.com.

NetVanta 1355 PWR

P/N 1200740L1

 

Quick Start Guide

NETVANTA1355 PWR FRONTPANELLAYOUT

POWER OVERETHERNET

Power over Ethernet (PoE) technology provides the ability to detect attached Powered Devices (PDs) and deliver 48 VDC to the PD via existing CAT5 cabling. The NetVanta 1355 PWR units are fully compliant with the power delivery options called out in the IEEE 802.3af Power over Ethernet specification. By default, the PoE interfaces discover and provide power to IEEE compliant PDs.

To disable power detection and supply, use the power inline never command in the CLI. To disable power detection and supply from the GUI, select thePorts page. Then select a single port from the list (e.g.,eth 0/1). This will bring up the port detail page foreth 0/1. On this page, there is a check box to enable power detection.

GETTINGSTARTED

Two configuration methods are available for your NetVanta 1355 PWR unit:

Web-basedGUI

AOS Command Line Interface (CLI)

The GUI lets you configure the main unit settings and provides online guidance and explanations for each setting. However, using the AOS CLI may be necessary for more advanced configurations.

ACCESS THECLI

Access the AOS CLI via the CONSOLE port or a Telnet session. To establish a connection to the NetVanta unit’sCONSOLE port, you need the following items:

VT100 terminal or PC (with VT100 terminal emulation software)

Straight-throughserial cable with aDB-9(male) connector on one end and the appropriate interface for your terminal or PC communication port on the other end

1.Connect the DB-9(male) connector of your serial cable to theCONSOLE port on the rear panel of the unit.

2.Connect the other end of the serial cable to the terminal or PC.

3.Insert the connector of the provided power cord into the power interface on the rear panel of the unit, and plug the cord into a standard electrical outlet.

4.Once the unit is powered up, open a VT100 terminal session using the following settings: 9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press <Enter> to activate the AOS CLI.

5.Enter enable at the> prompt. Enter the enable password when prompted. The default password ispassword.

ACCESS THEGUI

You can access the web-basedGUI from any web browser on your network by following these steps:

1.Connect the unit to your PC using the Ethernet (ETH 0/0) port on the rear of the unit.

2.Set your PC to obtain an IP address automatically via Dynamic Host Configuration Protocol (DHCP), or change your PC to a fixed IP address of 10.10.10.2. If you cannot change the PC’s IP address, you will need to change the unit’s IP address using the CLI. (Refer to the next two sections for instructions.)

3.Enter the unit’s IP address in your browser address line. The default IP address is 10.10.10.1.

4.You will then be prompted for the username and password (the default settings are admin andpassword).

5.The initial GUI screen appears.

The configuration parameters used in the examples outlined in this document are for instructional purposes only. Please replace all underlined entries (example) with your specific parameters to configure your application.

Quick Start Guide, 61200740L1-13A,March 2006

Technical Support 1-888-4ADTRAN(1-888-423-8726)

Copyright © 2006 ADTRAN, All Rights Reserved

®

 

For more detailed documentation, visit us online at www.adtran.com.

NetVanta 1355 PWR

P/N 1200740L1

 

Quick Start Guide

CF

SLOT 1

SLOT 2

MOH

0/1 0/2 0/1 0/2

PAGE

ANALOG STA ANALOG TRK

100-250VAC

50-60Hz

ETH 0/0

CONSOLE

DOOR

RELAY

NC NO COM

NETVANTA1355 PWR REARPANELLAYOUT

CONFIGURE THEUNITSIP ADDRESS

The following steps create an IP address and subnet mask for the ETH 0/0 interface and add a default route to the route table.

1.At the # prompt, enterconfig terminal.

2.Enter enable password password to assign an Enable Security mode password. This is necessary for Telnet configuration sessions.

3.Enter interface eth 0/0 to access the Ethernet port on the rear panel of the unit.

4.Enter ip address 10.10.10.1 255.255.255.0 to assign an IP address to the Ethernet port using a24-bitsubnet mask. Contact your Network Administrator to obtain the IP address (and subnet mask) for your particular configuration.

5.Enter no shutdown to activate the interface to pass data.

6.Enter exit to exit the interface commands and return to the Global configuration mode.

7.Enter ip route 0.0.0.0 0.0.0.0 10.10.10.2 to add a default route to the route table. Contact your Network Administrator to obtain the IP address of your default gateway.

ENABLETELNETACCESS

The following steps create a password of adtran for Telnet access. By default, Telnet access is enabled with a password ofpassword.

1.Verify that the prompt of your unit displays (config)#.

2.Enter line telnet 0 4 to change the configuration parameters for the Telnet sessions.

3.Enter login to initiate Telnet access.

4.Enter password adtran to change the login password for the Telnet sessions.

5.Enter exit to return to the Global Configuration mode.

6.Verify that the prompt of your unit displays (config)#.

7.Enter do write memory to save the current configuration.

ETHERNETPINOUTS

Pin

Name

Description

 

 

 

1

TX1

Transmit Positive

2

TX2

Transmit Negative

3

RX1

Receive Positive

4, 5

Unused

6

RX2

Receive Negative

7, 8

Unused

CONSOLEPINOUTS

Pin

Name

Description

 

 

 

1

DCD

Data Carrier Detect (output)

2

RD

Receive Data (output)

3

TD

Transmit Data (input)

4

DTR

Data Terminal Ready (input)

5

SG

Signal Ground

6

DSR

Data Set Ready (output)

7

Unused

8

CTS

Clear to Send (output)

9

Unused

Important: For additional details on product features, specifications, installation, and safety, refer to the appropriate Hardware Installation Guide on theADTRAN OS System Documentation CD shipped with the base unit and available online at www.adtran.com.

CONFIGUREYOURAPPLICATION

More detailed documentation for configuring your ADTRAN unit is provided on the ADTRAN OS System Documentation CD included in your shipment. For more detail on hardware setup, refer to the appropriate NIM Quick Start Guides and the Hardware Installation Guide. For more detail on configuring your system, refer to theADTRAN Operating System (AOS) Command Reference Guide, configuration guides, and technical support notes.

Quick Start Guide, 61200740L1-13A,March 2006

Technical Support 1-888-4ADTRAN(1-888-423-8726)

Copyright © 2006 ADTRAN, All Rights Reserved