ADTRAN 1204002L1 User Manual

Size:
940.96 Kb
Download

IQ Probe

Frame Relay

Monitoring Probe

USER MANUAL

IQ Probe Unit

1200214L1

ESP 4-wireSW56 DBU Card

1204001L1

ESP V.34 DBU Card

1204002L1

ESP ISDN DBU Card

1204004L1

ESP External DCE Card

1204006L1

61200214L1-1AAugust 1998

Trademark Information:

OpenView is a registered trademark of Hewlett-PackardCompany. SunNet Manager is a registered trademark of Sun Microsystems, Inc. Netview is a registered trademark of IBM.

IQ View is a trademark of ADTRAN, Inc.

This product includes software developed by the University of California, Berkeley, and its contributors.

901 Explorer Boulevard

P.O. Box 140000

Huntsville, AL 35814-4000

Phone: (256) 963-8000

© 1998 ADTRAN, Inc.

All rights reserved.

Printed in USA.

ABOUT THIS MANUAL

This manual is arranged so you can quickly and easily find the information you need. The following is an overview of the contents of this manual:

Chapter 1, Introduction, familiarizes you with frame relay networks and IQ Probe highlights.

Chapter 2, Installation, describes the IQ Probe connectors (pin assignments are given in Appendix A) and provides an installation diagram.

Chapter 3, Operation, explains how to operate your IQ Probe using either the front panel or a terminal interface.

Chapter 4, Applications, provides examples of some common IQ Probe applications. This chapter includes network diagrams as well as configuration examples.

Chapter 5, Configuration Overview, explains how to access the IQ Probe configuration menu and provides menu trees for both the front panel and the terminal interface.

Chapters 6 through 9 provide brief explanations for selections made in the Configuration menus. These chapters are based on the first level menu branches of the Configuration menu: DTE Port, DCE Port, Dial Backup, and System Configuration.

Chapter 10, Statistics, describes how to access statistical information from the IQ Probe.

Chapter 11, Testing, explains how to access the IQ Probe diagnostic features, including PVC loopback and ping tests.

Chapter 12, Activating Dial Backup Options, provides information on the dialing options accessed through the Main menu.

Appendix A provides pinouts for the IQ Probe connectors.

Appendix B contains product specifications.

Notes provide additional useful information.

Cautions signify information that could prevent service interruption.

Warnings provide information that could prevent damage to the equipment or endangerment to human life.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

When using your telephone equipment, please follow these basic safety precautions to reduce the risk of fire, electrical shock, or personal injury:

1.Do not use this product near water, such as near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.

2.Avoid using a telephone (other than a cordless-type)during an electrical storm. There is a remote risk of shock from lightning.

3.Do not use the telephone to report a gas leak in the vicinity of the leak.

4.Use only the power cord, power supply, and/or batteries indicated in the manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for special disposal instructions.

FCC regulations require that the following information be provided in this manual:

1.This equipment complies with Part 68 of the FCC rules. On the bottom of the ESP DBU card is a label that shows the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, provide this information to the telephone company.

2.If this equipment causes harm to the telephone network, the telephone company may temporarily discontinue service. If possible, advance notification is given; otherwise, notification is given as soon as possible. The telephone company will advise the customer of the right to file a complaint with the FCC.

3.The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the proper operation of this equipment; advance notification and the opportunity to maintain uninterrupted service are given.

4.If experiencing difficulty with this equipment, please contact ADTRAN for repair and warranty information. The telephone company may require this equipment to be disconnected from the network until the problem is corrected, or it is certain the equipment is not malfunctioning.

5.This unit contains no user-serviceableparts.

6.An FCC compliant telephone cord with a modular plug is provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using an FCC compatible modular jack, which is Part 68 compliant.

7.The following information may be required when applying to the local telephone company for dial backup service:

Service Type

REN/SOC

FIC

USOC

56 kbps Digital Interface

6.0F

04DU5-56

RJ-48S

64 kbps Digital Interface

6.0F

04DU5-64

RJ-48S

Loop Start (V.34)

0.8B/0.4A

02LS2

RJ-11C

8.The REN is useful in determining the quantity of devices you may connect to your telephone line and still have all of those devices ring when your number is called. In most areas, the sum of the RENs of all devices should not exceed five. To be certain of the number of devices you may connect to your line as determined by the REN, call your telephone company to determine the maximum REN for your calling area.

9.This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs. (Contact your state public utility commission or corporation commission for information.)

FEDERAL COMMUNICATIONS COMMISSION

RADIO FREQUENCY INTERFERENCE STATEMENT:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio frequencies. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Shielded cables must be used with this unit to ensure compliance with Class A FCC limits.

Change or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

CANADIAN EMISSIONS REQUIREMENTS

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causingequipment standard entitled "Digital Apparatus,"ICES-003of the Department of Communications.

Cet appareil nuerique respecte les limites de bruits radioelectriques applicables aux appareils numeriques de Class A prescrites dans la norme sur le materiel brouilleur: "Appareils Numeriques," NMB-003edictee par le ministre des Communications.

CANADIAN EQUIPMENT LIMITATIONS

Notice: The Canadian Industry and Science Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company's inside wiring associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or an electrician, as appropriate.

The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the Load Numbers of all devices does not exceed 100.

ISDN Service Ordering Information for the ADTRAN IQ Probe With ISDN Dial Backup

For ADTRAN IQ Probe ISDN dial backup applications, the following guide can be used as an aid in ordering basic ISDN service from your local telephone company. The ADTRAN IQ Probe ISDN includes NT1 and Terminal adapter functionality and supports data rates up to 128 kbps.

Request an ISDN Basic Rate Interface (BRI) line with the following features:

U-interfacereference point 2B1Q line coding

1B+D Service (supports up to 64 kbps) 2B+D Service (supports up to 128 kbps)

The IQ Probe ISDN supports the following switch types and software protocols:

Lucent 5ESS

Custom, 5E6 and later software, National ISDN-1

NT1 DMS-100

BCS-32and later software (Pvc1), NationalISDN-1(Pvc2)

Siemens EWSD

National ISDN-1

Request that the ISDN line allocate one DYNAMIC Terminal Endpoint Identifier (TEI) for the number.

For service offered from an Lucent 5ESS, request a point-to-pointline with the following features:

Feature: Value

B1 Service: On Demand (DMD)

Data Line Class: Point-to-Point

Maximum B Channels: 1 (1B+D) or 2 (2B+D) Circuit Switched Data (CSD) Bearer Channels:Any Number of CSD Calls:1 (1B+D) or 2 (2B+D) Terminal Type:Type A

Turn the Following Features Off:

Packet Mode Data

Multi-lineHunt

Multiple Call Appearances

Electronic Key Telephone Sets (EKTS)

Shared Dictionary Numbers

Accept Special Type of Number

Intercom Groups

Network Resource Selector (Modem Pools)

Message Waiting

Hunting

InterLata Competition

For service offered from a Northern Telecom DMS-100,request aPoint-to-PointMulti-Pointline with the following features:

Line Type: Basic Rate, Functional

Electronic Key Telephone Sets (EKTS): No

Call Appearance Handling (CACH): No Non-InitializingTerminal:No

Circuit Switched Service: Yes

Packet Switched Service: No

TEI: Dynamic

Bearer Service: Circuit Switched voice and data permitted on any B channel (packet mode data not permitted)

Table of Contents