- •Contents
- •ER Enterprise Reporter Introduction
- •About this Document
- •Conventions Used in this Document
- •Service Information
- •Preliminary Setup Procedures
- •Unpack the Unit from the Carton
- •Select a Site for the Server
- •Install the “H” Server Bezel
- •Rack Mount the Server
- •Check the Power Supply
- •General Safety Information
- •Install the Server
- •Step 1: Setup Procedures
- •Step 1A: Quick Start Setup Procedures
- •Step 1B: Console Setup Procedures
- •Step 3: R3000 Configuration
- •Step 4: Client Workstation Configuration
- •Step 5: Launch the ER Client
- •Conclusion
- •Important Information about using the ER in the Evaluation Mode
- •Administrator Console, Expiration Screen
- •ER Client, ER Server Statistics Window
- •Non-“H” Server Specifications
- •Physical Specifications
- •Hardware Component Specifications
- •Internal Product Specifications
- •Front Panel LED Indicators and Buttons
- •“H” Server Specifications
- •Physical Specifications
- •Hardware Component Specifications
- •Internal Product Specifications
- •Front of Chassis: Control Panel
- •Rear of Chassis
- •Regulatory Specifications and Disclaimers
- •Declaration of the Manufacturer or Importer
- •Appendix: SCSI Connected Storage Device
- •Preliminary Setup Procedures
- •Install the Unit
- •Physical Components
- •Specifications

Install theServer
Step 1: Setup Procedures
This step requires you to link the workstation to the ER. You have the option of using the
Quick Start Setup Requirements
The following hardware can be used for the Quick Start setup procedures:
•ER with AC power cord
•either one of two options:
•PC monitor with AC power cord and keyboard, or
•PC laptop computer with HyperTerminal and serial port cable (and USB DB9 serial adapter, if there is no serial port on your laptop)
Go to Step 1A to execute Quick Start Setup Procedures.
Administrator Console Setup Requirements
The following hardware is required for the Administrator console setup procedures:
•ER with AC power cord
•
•PC laptop computer, or PC monitor with AC power cord and keyboard
Go to Step 1B to execute Console Setup Procedures.
8e6 EnterpriseReporterQuickStartGuide | 21 |

Step 1A: Quick Start Setup Procedures
Storage Device Setup (for Attached Storage Units)
If you have a NAS (SCSI Connected Storage Device or “SAN”) that will be used with the ER, you will need to connect it to the ER at this point. Refer to the Appendix at the end of this document for instructions on how to connect the SCSI Connected Storage Device.
Link the Workstation to the ER
Monitor and Keyboard Setup
A.Connect the PC monitor and keyboard cables to the rear of the chassis.
B.Turn on the PC monitor.
C.Power on the ER by dropping down the face plate and pressing the large button at the right of the front panel (see image below).
Front of the 1U chassis
Once the ER is powered up, proceed to the Login screen instructions.
Serial Console Setup
A.Using the serial port cable (and USB DB9 serial adapter, if necessary), connect the laptop to the rear of the chassis (see image below).
Rear of the 1U chassis
B.Power on the laptop.
C.Power on the ER by dropping down the face plate and pressing the large button at the right of the front panel (see first image above).
Once the ER is powered up, proceed to the instructions for HyperTerminal Setup Procedures.
22 | 8e6 EnterpriseReporterQuickStartGuide |

HyperTerminal Setup Procedures
If using a serial console, follow these procedures to create a HyperTerminal session.
A.Launch HyperTerminal by going to Start > Programs > Accessories > Communications > HyperTerminal:
B.In the Connection Description dialog box, enter any session Name, and then clickOK to open the Connect To dialog box:
8e6 EnterpriseReporterQuickStartGuide | 23 |

C.At the Connect using field, select the COM port assigned to the serial port on the laptop (probably “COM1”), and then clickOK to open the Properties dialog box, displaying the Port Settings tab:
D.Specify the following session settings:
•Bits per second: 9600
•Data bits: 8
•Parity: None
•Stop bits: 1
•Flow control: Hardware
E.Click OK to connect to the HyperTerminal session:
24 | 8e6 EnterpriseReporterQuickStartGuide |

F.In the HyperTerminal session window, go to File > Properties to open the Properties dialog box, displaying the Connect To and Settings tabs:
G.Click the Settings tab, and at the Emulation menu select “VT100”.
H.Click OK to close the dialog box, and to go to the login screen.
NOTE: If using a HyperTerminal session, the login screen will display with black text on a white background.
8e6 EnterpriseReporterQuickStartGuide | 25 |

Login screen
The login screen displays after powering on the ER unit using a monitor and keyboard, or after creating a HyperTerminal session.
NOTE: If the screensaver currently displays on your screen, press theEnter key to display the login screen.
A.At the login prompt, type inmenu.
B.Press the Enter key to display the Password prompt.
C.At the Password prompt, type in the following:#s3tup#r3k
D.Press Enter to display the Quick Start menu screen.
Quick Start menu screen
A.At the Press the number of your selectionprompt, press 2to select the Quick Start setup process.
B.At the login prompt,
C.Press Enter to display the administration menu where you can begin using the Quick Start setup procedures.
26 | 8e6 EnterpriseReporterQuickStartGuide |

Quick Start menu: administration menu
A.At the Press the number of your selectionprompt, press 2to select the “Quick Start Setup” process.
The Quick Start menu takes you to the following configuration screens to make entries:
•Configure network interface LAN1
•Configure default gateway
•Configure DNS servers
•Configure host name
•Time Zone regional setting
NOTE: See the Network screens for Network Settings, and Regional Setting in Step 1B for content included in the Quick Start setup screens.
B.After making all entries using the Quick Start setup procedures, press X to return to the Quick Start menu screen. Or, to verify the status of the ER and review the entries you made using the Quick Start setup, press1 to view the System Status screen.
NOTE: Changing your password using option C, “Change Quick Start password”, will change the password for the console menu but not the ER console login screen. Option D, “Reset admin console account”, should be used for resetting the administratorconsoleusernameandpasswordtothefactorydefault‘admin’/’reporter’ and for unlocking all IP addresses currently locked.
8e6 EnterpriseReporterQuickStartGuide | 27 |

System Status screen
The System Status screen contains the following information:
•Capturing Interface specified in screen 3 (Configure network interface LAN1)
•lan1 IP address and netmask specified in screen 3, and current status (“Active” or
“Inactive”)
•Default gateway IP address specified in screen 4 (Configure default gateway)
•ER host name specified in screen 6 (Configure host name)
•DNS server IP address(es) specified in screen 5 (Configure DNS servers)
•Regional timezone setting specified in screen 7 (Time Zone regional setting)
•Current status of the ER
•Current ER software Version installed
NOTE: Modifications can be made at any time by returning to the specific screen of the Quick Start procedures.
Log Off, Disconnect the Peripherals
A.After completing the Quick Start setup procedures, return to the Quick Start menu screen and press 9 to log out.
B.Disconnect the peripherals from the ER.
28 | 8e6 EnterpriseReporterQuickStartGuide |