4XEM IPCAMW45 User Manual

Size:
3.17 Mb
Download

Security Settings

Root password: Change the Administrator’s password by typing in the new password identically in both text boxes. The typed entries will be displayed as asterisks for security purposes. After pressing, the web browser will ask the Administrator for the new password for access.

Add user: Type the new user's name and password and pressto insert the new entry. The new user will be displayed in the user name list. There is a maximum of twenty user accounts. Checking I/O access can enable user to use D/I and D/O applications

Manager user: Pull down the user list to find the user’s name and pressto complete.

- 17 -

www.4XEM.com

Network Settings

Any changes made on this page will restart the system in order to validate the changes. Make sure every field is entered correctly before clicking on .

Network Type

LAN & PPPoE:

The default type is LAN. Select PPPoE if using ADSL

Get IP address automatically & Use fixed IP address:

The default status is Get IP address automatically. This can be tedious having to perform software installation whenever the Network Camera starts.

Therefore, once the network settings, especially the IP address, have been entered correctly, select Use fixed IP address then the Network Camera will skip installation at the next boot. The Network Camera can automatically restart and operate normally after a power

outage. Users can run IP installer to check the IP address assigned to the Network Camera if the IP address is forgotten or using the UPnP function provided by the Network Camera (MS Windows XP provides UPnP function at My Network Place).

IP address: This is necessary for network identification.

Subnet mask: This is used to determine if the destination is in the same subnet. The default value is “255.255.255.0”.

Default router: This is the gateway used to forward frames to destinations in a different subnet.

- 18 -

www.4XEM.com

Primary DNS: The primary domain name server that translates hostnames into IP addresses.Secondary DNS: Secondary domain name server that backups the Primary DNS.

Enable UPnP presentation: Enable the UPnP camera short cut

Enable UPnP port forwarding: Enable uPnP port forwarding

PPPoE: If using the PPPoE interface , fill the following settings from ISPUser name: The login name of PPPoE account

Password: The password of PPPoE account

Confirm password: Input password again for confirmation

HTTP

Http port: This can be other than the default Port 80. Once the port is changed, the users must be notified of the change for the connection to be successful. For instance, when the Administrator changes the HTTP port of the Network Camera whose IP address is 192.168.0.100 from 80 to 8080, the users must type in the web browser “http://192.168.0.100:8080” instead of “http://192.168.0.100”.

RTSP Streaming

Access name: This is the access URL for making connection from client software. Using rtsp://<ip address>/<access name> to make connection

RTSP port: This can be other than the default Port 554

DDNS

Enable DDNS: This option turns on the DDNS function.

Provider: The provider list contains four hosts that provide DDNS services. Please connect to the service provider’s website to make sure the service charges.

Host Name: If the User

- 19 -

www.4XEM.com

wants to use DDNS service, this field must be filled. Please input the hostname that is registered in the DDNS server.

Username/E-mail: The Username orE-mailfield is necessary for logging in the DDNS server or notify the User of the new IP address. Note: when this field is input as “Username” the following field must be input as “Password”.

Password/Key: Please input the password or key to get the DDNS service.

Save: Click on this button to save current settings for the DDNS service and UPnP function.

Access List

The access list is to control the access permission of clients by checking the client IP address.

There are two lists for permission control: Allow List andDeny List. Only those clients whose IP address is in theAllow List and not in theDeny List can connect to the Video Server or

Network Camera for receiving the audio/video streaming.

Both Allow List andDeny List consist of a list of IP ranges. If you want to add a new IP address range, type theStart IP Address andEnd IP Address in the text boxes and click on theAdd button. If you want to remove an existing IP address range, just select from thepull-downmenu and click on theDelete button.

Both the Allow List and Deny List can have 20 entries.

- 20 -

www.4XEM.com

Audio and Video

General

Configure for computer viewing: To make quick setting for computer viewing.Configure for mobile viewing: To make quick setting for cell phone viewing.

Video Settings

Video title: The text string can be displayed on video

Color: Select either for color or monochrome video display.

Frame Size: There are four options for video sizes. 160x120,

176x144, 320x240, & 640x480.

Power line frequency (for fluorescent light):

Change the frequency setting to eliminate

uncomfortable flash image when the light source is only fluorescent light.

There are three dependent parameters provided for video performance adjustment.

Max frame rate: Allows you to specify the maximum number of frames per second generated by the camera.

Maximum Exposure Time: Adjusts the shutter speed of the camera to allow for exposure adjustments.

Key frame interval: Determines how often full data frames are sent from the camera in the MPEG4 video stream. Lower key frame intervals improve the overall quality of the image at a cost of bandwidth usage and storage requirements.

Video Quality: This section allows you to force the camera to either operate within a certain bandwidth or maintain a certain quality level.

- 21 -

www.4XEM.com

Video Orientation

Flip: Vertically rotate the video.

Mirror: Horizontally rotate the video. Check both options if the Network Camera is installed upside down.

White balance: Adjust the value for best color temperature.

Audio settings

Use: Switchinternal ormicrophone to set up the source of audio inputMute: Audio mute

Boost external microphone input: Enhance the gain of the external microphoneInternal input Gain: Modify the gain of the internal audio input

Audio type: Select audio codecAAC orGSM-AMR and the bit rate

Image Settings

Click on this button to pop up another window to tuneBrightness,

Contrast, Hueand Saturationfor video compensation. Each field has eleven levels ranged from -5 to +5. In Brightnessand Contrastfields the value 0 indicates auto tuning. The user may press to fine-tune the image. When the image is O.K., press to set the image settings.

Click on this to recall the original settings without incorporating the changes.

- 22 -

www.4XEM.com

Email & FTP

Email

When the SMTP server supports SMTP authentication, users need to give the valid user name and password to send email via the server.

Sender email address: the email address of the sender.

There are two external mail servers that can be configured: primary and secondary. The network

camera will use the primary server as a default, and use the secondary server when the primary server is unreachable.

Server address: The domain name or IP address of the external email server.User name: This granted user name on the external email server.Password: This granted password on the external email server.

Recipient email address: The email address of the recipients for snapshots or log file. Multiple recipients must be separated by a semicolon (;).

- 23 -

www.4XEM.com

FTP

Built-in FTP server port number: This can be other than the default port 21. The user can change this value from 1025 to 65535. After a change, the external FTP client program must change the server port

of connection accordingly.

There are two external FTP servers that can be configured: primary and secondary. The network camera will use the primary server as a default, and use the secondary server when the primary server is unreachable.

Server address: The

domain name or the IP address of the external FTP server. The following user settings must be correctly configured for remote access.

FTP server port: This can be other than the default port 21. The user can change this value from 1025 to 65535.

User name: Granted user name on the external FTP server.Password: Granted password on the external FTP server.

Remote folder name: Granted folder on the external FTP server. The string must conform to that of the external FTP server. Some FTP servers cannot accept preceding slash symbol before the path without virtual path mapping. Refer to the instructions for the external FTP server for details. The folder privilege must be open for upload.

- 24 -

www.4XEM.com

Motion Detection

Enable motion detection: Check this option to turn on motion detection.

Click on this button to add a new window. At most three windows can exist simultaneously. Use the mouse to click, hold, and drag the window frame to resize or the title bar to move. Clicking on the ‘x’ at the upperright-handcorner of the window to delete the window. Remember to save in order to validate the changes.

Click on this button to save the related window settings. A graphic bar will rise or fall depending on the image variation. A green bar means the image variation is under monitoring level and a red bar means the image variation is over monitoring level. When the bar goes red, the detected window will also be outlined in red. Going back to the homepage, the monitored window is hidden but the red frame shows when motion is detected.

Window Name: The text will show at the top of the window.

Sensitivity: This sets the endurable difference between two sequential images.Percentage: This sets the space ratio of moving objects in the monitoring window. Higher sensitivity and small percentage will allow easier motion detection.

The following figure shows the screen when is clicked. The monitoring window has been outlined in red and the graphic bar goes red since the goldfish is moving.

- 25 -

www.4XEM.com

Application Settings

Application

There are four Applications available: two snapshots, one video clip and one digital input, all with the following settings. Status: ON/OFF show the status of application.

Sun - Sat: Select the days of the week to perform the application.

Time: Show Alwaysor input the time interval.

Trigger: Event trigger type has digital input, motion detection and is sequential.

Send: After Event has been triggered, IP cam will send something by email, ftp or trigger digital output.

Snapshot

Snapshot

Enable snapshot:

Enable/Disable snapshot application.

Weekly Schedule

Sun - Sat: Select the days of the week to perform the application.

- 26 -

www.4XEM.com