3M 3M-MATIC 700R-S BROCHURE User Manual

Size:
225.91 Kb
Download

3M-Matic Stainless Steel Random Case Sealer700r-s

Specifications:

Box:

Style: Regular slotted container (RSC)

Bursting test: 125 to 275 lbs. per sq. inch single or double wall, B or C flute.

Size:

Min

Max

Length

6" (150mm)

21.5" (546mm)

Width

6" (150mm*)

No limit

Height

4.75" (121mm)

24.5" (622mm)

*3.75" [90mm] with taping heads adjusted to apply 2" [51mm] tape leg lengths and upper mast stops relocated.

Weight: Up to 85 lbs. [38.6kg] Packing: Contents must support flaps.

Note: The3M-Matic 700r-scan accommodate most boxes within the size range listed above. However, if

Box length in Direction of Seal is less than .5 Box Height

boxes should be test run to ensure proper machine performance.

Tape:

Scotchbrand pressure sensitive box sealing tapes.

Width: 1.5 inches [36mm] minimum to 2 inches [50mm] maximum Roll diameter: up to 16 inches [406mm] maximum on a 76.2mm

diameter on 3 inch [76.2mm] diameter core.

Machine:

Power:

Electrical — 115 V, 60Hz, 3.8A , 440 watts, 8 ft. [2.4m] power cord with grounded plug included.

Pneumatic – 70 PSIG [4.8 bar gauge pressure] 3.75 SCFM [.14 l/min @ 21°C, 1.01 bar] at 15 boxes per minute.

A pressure regulator is included. Weight:

429 lbs.[194.6kg] uncrated

501 lbs. [227kg] crated

Operating rate: Up to 15 boxes per minute. Actual production rate is dependent on box size, box size mix, and operator dexterity

box length.

Box drive belt speed: 75 fpm [.38 m/s]

Operating conditions: Use in relatively clean environments at 40°F to 120°F with clean, dry boxes.

Machine should not be washed down.

Footprint:

 

 

T

Infeed

Infeed/Exit

 

L

 

Conveyor

Conveyor

 

 

 

 

Supplied

F

W

Box Travel

F

 

 

 

 

A

 

Control Side

 

H

B

C

Air Hose

 

Connection

 

W

L

H

A*

B

C*

F

Min inches (mm)

31(787)

40.5 (1030)

53 (1346)

18 (457)

24 (610)

4 (102)

24.5 (622)

Max inches (mm)

31(787)

40.5 (1030)

86 (2184)

18 (457)

35 (889)

4 (102)

24.5 (622)

Masts in upper

 

 

90 (2290)

 

20.5 (521)

 

 

position

 

 

max

 

min

 

 

 

 

 

 

 

31 [780] max

 

 

* Exit conveyors are optional

T=64.5 (1637)

 

 

 

 

** Casters are optional

 

 

 

 

 

 

Product Use: User is responsible for determining whether the product is fit for a particular purpose and suitable for user’s method of application.

Warranty and Limited Remedy: THE FOLLOWING WARRANTIES ARE MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED

TO THE IMPLIED WARRANTY OF MERCHANTABILITY, THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OF DEALING, A CUSTOM OR USAGE OF TRADE: 3M sells its 3M-Matic Stainless Steel Random Case Sealer700r-swith the following warranties: 1) The Taping Head knife blades, springs and rollers will be free from all defects for ninety (90) days after delivery. 2) All other Taping Head parts will be free from all defects for three (3) years after delivery. 3) All other parts will be free from all defects for two (2) years after delivery.

Please refer to individual data pages for additional details and exceptions.

If any 3M-warrantiedpart is proved to be defective within its warranty period, then the exclusive remedy and 3M’s and seller’s sole obligation shall be, at 3M’s option, to repair or replace the part, provided the defective part is returned immediately to 3M’s factory or an authorized service station designated by 3M. A part will be presumed to have become defective after its warranty period unless the part is received or 3M is notified of the problem no later than five (5) calendar days after the warranty period. If 3M is unable to repair or replace the part within a reasonable time, then 3M, at its option, will replace the equipment or refund the purchase price. 3M shall have no obligation to

provide or pay for the labor required to install the repaired or replacement part. 3M shall have no obligation to repair or replace (1) those parts failing due to operator misuse, carelessness, or due to any accidental cause other than equipment failure, or (2) parts failing due to non-lubrication,inadequate cleaning, improper operating environment, improper utilities or operator error.

Limitation of Liability: 3M and seller shall not be liable for direct, indirect, special, incidental or consequential damages based upon breach of warranty, breach of contract, negligence, strict liability or any other legal theory.

The foregoing Warranty and Limited Remedy and Limitation of Liability may be changed only by a written agreement signed by authorized officers of 3M and seller.

3

Industrial Business

Industrial Adhesives and Tapes Division

Bldg. 21-1W-10

900 Bush Ave.

St. Paul, MN 55106 1-800-362-3550www.3M.com/packaging

AccuGlide,3M-Matic,and Scotch® are trademarks of 3M.

Printed in U.S.A. © 3M 2005

70-0710-0318-3

3

3M-Matic

Stainless Steel

Random Case Sealer 700r-s

Productivity in corrosive environments

3M-Matic Stainless Steel Random Case Sealer700r-s…automatic productivity

For durability and productivity in high-moistureand corrosive packaging operations, the3M-Matic

Stainless Steel Random Case Sealer 700r-sconforms to NEMA standard 250 type 4x specifications for watertight enclosures.

Engineered with 99% stainless steel for corrosion resistance, there are no painted surfaces.

For productivity, the 700r-sseals up to 15 different size cases per minute, automatically adjusting to height and width of each box.

Wide range of case sizes from as small as 4.75" high x 6" wide to as large as 24.5" high x 21.5" wide.

Sturdy construction easily handles case weights up to 85 lbs.

Compact footprint saves floor space.

Easy-to-installand use, you’ll be quickly making consistent

seals on a wide range of RSCs with minimal operator training.

3MAccuGlide

Stainless Steel Taping Head

Designed for high moisture and corrosive environments but not for direct high pressure wash down

Upper and lower heads easily removed for service

Instructional and safety labeling

Permanently bonded to resist distortion from heat and humidity

Dual masts

Provides greater stability of taping head position

Reliable gearmotor drive

Heavy-dutyto handle up to85-lb.cases

Sturdy top belt drive

Traction-gripsurface on belts for reliable feeding of wide range of case weights

Laced construction for replacement ease

Optional infeed/exit conveyor

Roller shafts locked in position for reliable performance

Ball bearing rollers for smooth motion

Optional casters

Caster brake and locking swivel for on the job stability

Large 4" diameter polyolefin tires for easy movement

Air filter/regulator/gauge

Lock-outon/off air valve to maintain proper pressure

Friction drum brake to maintain proper tape tension and prevent overcoasting

for smooth tape application

Box Capacities

Length: 6" to 30"

Width: 4.75" to 21.5"

Height: 4.75" to 24.5"

station

Keep cases centered under the taping head

Adjust for box width

Panel mounted on/off switch

Easy access

Can be repositioned to either side for easy access and line changes

Adjustable leg height

Graduated for precise adjustment from 24" to 35" bed height (without casters)

Centering arm guard

• Operator safety