3COM WL-542 User Manual

0 (0)

OfficeConnect®

ADSL Wireless 11g Firewall Router

User Guide

Model WL-542

3CRWDR100A-72 3CRWDR100B-72 3CRWDR100U-72

http://www.3com.com/

Part No. DUA100A-72AAA02

Published August 2005

3Com Corporation

350 Campus Drive,

Marlborough, MA

USA 01752-3064

Copyright © 2004, 2005, 3Com Corporation. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without written permission from 3Com Corporation.

3Com Corporation reserves the right to revise this documentation and to make changes in content from time to time without obligation on the part of 3Com Corporation to provide notification of such revision or change.

3Com Corporation provides this documentation without warranty, term, or condition of any kind, either implied or expressed, including, but not limited to, the implied warranties, terms or conditions of merchantability, satisfactory quality, and fitness for a particular purpose. 3Com may make improvements or changes in the product(s) and/or the program(s) described in this documentation at any time.

If there is any software on removable media described in this documentation, it is furnished under a license agreement included with the product as a separate document, in the hard copy documentation, or on the removable media in a directory file named LICENSE.TXT or !LICENSE.TXT. If you are unable to locate a copy, please contact 3Com and a copy will be provided to you.

UNITED STATES GOVERNMENT LEGEND

If you are a United States government agency, then this documentation and the software described herein are provided to you subject to the following:

All technical data and computer software are commercial in nature and developed solely at private expense. Software is delivered as “Commercial Computer Software” as defined in DFARS 252.227-7014 (June 1995) or as a “commercial item” as defined in FAR 2.101(a) and as such is provided with only such rights as are provided in 3Com’s standard commercial license for the Software. Technical data is provided with limited rights only as provided in DFAR 252.227-7015 (Nov 1995) or FAR 52.227-14 (June 1987), whichever is applicable. You agree not to remove or deface any portion of any legend provided on any licensed program or documentation contained in, or delivered to you in conjunction with, this User Guide.

Unless otherwise indicated, 3Com registered trademarks are registered in the United States and may or may not be registered in other countries.

3Com, and the 3Com logo are registered trademarks of 3Com Corporation.

Intel and Pentium are registered trademarks of Intel Corporation. Microsoft, MS-DOS, Windows, and Windows NT are registered trademarks of Microsoft Corporation. Novell and NetWare are registered trademarks of Novell, Inc. UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open Company, Ltd.

Netscape Navigator is a registered trademark of Netscape Communications.

JavaScript is a trademark of Sun Microsystems

Wi-Fi and the Wi-Fi logo are registered trademarks of the WI-Fi Alliance.

IEEE and 802 are trademarks of the Institute of Electrical and Electronics Engineers, Inc.

All other company and product names may be trademarks of the respective companies with which they are associated.

ENVIRONMENTAL STATEMENT

It is the policy of 3Com Corporation to be environmentally-friendly in all operations. To uphold our policy, we are committed to:

Establishing environmental performance standards that comply with national legislation and regulations.

Conserving energy, materials and natural resources in all operations.

Reducing the waste generated by all operations. Ensuring that all waste conforms to recognized environmental standards. Maximizing the recyclable and reusable content of all products.

Ensuring that all products can be recycled, reused and disposed of safely.

Ensuring that all products are labelled according to recognized environmental standards.

Improving our environmental record on a continual basis.

End of Life Statement

3Com processes allow for the recovery, reclamation and safe disposal of all end-of-life electronic components.

Regulated Materials Statement

3Com products do not contain any hazardous or ozone-depleting material.

Environmental Statement about the Documentation

The documentation for this product is printed on paper that comes from sustainable, managed forests; it is fully biodegradable and recyclable, and is completely chlorine-free. The varnish is environmentally-friendly, and the inks are vegetable-based with a low heavy-metal content.

CONTENTS

ABOUT THIS GUIDE

 

Naming Convention

5

 

 

 

Conventions

6

 

 

 

 

 

Feedback About this User Guide 6

 

 

Related Documentation

7

 

 

 

 

1 INTRODUCING THE ROUTER

 

 

OfficeConnect ADSL Wireless 11g Firewall Router

9

 

Router Advantages

11

 

 

 

Package Contents

11

 

 

 

Minimum System and Component Requirements

12

 

Front Panel

12

 

 

 

 

 

Rear Panel

13

 

 

 

 

 

 

 

2 INSTALLING THE ROUTER

 

 

Introduction

15

 

 

 

 

 

Safety Information

15

 

 

Positioning the Router

15

 

 

Using the Rubber Feet

16

 

 

Powering Up the Router

16

 

 

Connecting the Router

 

16

 

 

 

 

3 SETTING UP YOUR COMPUTERS

 

 

Obtaining an IP Address Automatically 21

 

 

Windows 2000

21

 

 

 

Windows XP

23

 

 

 

 

Windows 98/ME

23

 

 

 

Macintosh 23

 

 

 

 

Disabling PPPoE and PPTP Client Software 24

 

 

Disabling Web Proxy

24

 

4 RUNNING THE SETUP WIZARD

Accessing the Setup Wizard 25

Setup Wizard - Connection Type 27

5 CONFIGURING THE ROUTER

Navigating Through the Router Configuration Pages 35

Main Menu

35

 

 

Status Screen

35

 

 

Status

35

 

 

 

LAN Setup

36

 

 

 

LAN Settings

37

 

 

Wireless Settings

39

 

 

Configuring Wireless

39

Encryption

40

 

 

Internet Settings

46

 

 

Connection Type

46

 

DNS

55

 

 

 

 

Hostname & MAC

56

 

Firewall

57

 

 

 

 

Special Applications

58

Virtual Servers

59

 

Client IP Filters

60

 

MAC Address Filtering

65

DMZ

66

 

 

 

 

Advanced

68

 

 

 

Routing

70

 

 

 

DDNS

73

 

 

 

SNMP

74

 

 

 

System Tools

75

 

 

Restart Router

75

 

Reset to Factory Default

76

Backup/Restore Settings

76

Upgrade

77

 

 

 

Admin Password

77

 

Time and Time Zone 78

Syslog Server

79

 

 

Status and Logs

80

 

 

Status

80

 

ADSL Status 80

ATM PVC Status

81

Logs 81

 

Support/Feedback

82

Support

82

 

Feedback

82

 

6

TROUBLESHOOTING

 

 

Basic Connection Checks

83

 

Browsing to the Router Configuration Screens 83

 

Connecting to the Internet

84

 

Forgotten Password and Reset to Factory Defaults 84

 

Wireless Networking 85

 

 

Recovering from Corrupted Software 87

 

Frequently Asked Questions

88

A

 

 

IP ADDRESSING

 

 

The Internet Protocol Suite

89

Managing the Router over the Network 89 IP Addresses and Subnet Masks 89

How does a Device Obtain an IP Address and Subnet Mask? 91

DHCP Addressing

91

Static Addressing

91

Auto-IP Addressing

91

B TECHNICAL SPECIFICATIONS

OfficeConnect ADSL Wireless 11g Firewall Router 93

Standards 94

CSAFETY INFORMATION

DEND USER SOFTWARE LICENSE AGREEMENT

EOBTAINING SUPPORT FOR YOUR PRODUCT

Register Your Product

103

 

Purchase Value-Added Services

103

Troubleshoot Online

104

 

Access Software Downloads

104

Telephone Technical Support and Repair 104

Contact Us 105

GLOSSARY

REGULATORY NOTICES

INDEX

ABOUT THIS GUIDE

This guide describes how to install and configure the OfficeConnect ADSL

Wireless 11g Firewall Router (3CRWD100x-72).

This guide is intended for use by those responsible for installing and setting up network equipment; consequently, it assumes a basic working knowledge of LANs (Local Area Networks) and Internet Routers.

If a release note is shipped with the ADSL 11g Wireless Router and contains information that differs from the information in this guide, follow the information in the release note.

Most user guides and release notes are available in Adobe Acrobat Reader Portable Document Format (PDF) on the 3Com World Wide Web site:

http://www.3com.com

Naming Convention Throughout this guide, the OfficeConnect ADSL Wireless 11g Firewall Router is referred to as the “Router”.

Category 3 and Category 5 Twisted Pair Cables are referred to as Twisted

Pair Cables throughout this guide.

6 ABOUT THIS GUIDE

Conventions

Table 1 and Table 2 list conventions that are used throughout this guide.

 

Table 1

Notice Icons

 

 

 

 

 

 

Icon

Notice Type

Description

 

 

 

 

 

Information note Information that describes important features or

 

 

 

instructions.

 

 

Caution

Information that alerts you to potential loss of data or

 

 

 

potential damage to an application, system, or device.

 

 

Warning

Information that alerts you to potential personal

 

 

 

injury.

 

 

 

 

Table 2

Text Conventions

 

 

 

 

Convention

Description

 

 

 

 

The words “enter”

When you see the word “enter” in this guide, you must type

 

and “type”

something, and then press Return or Enter. Do not press

 

 

 

Return or Enter when an instruction simply says “type.”

 

 

 

 

Keyboard key names

If you must press two or more keys simultaneously, the key

 

 

 

names are linked with a plus sign (+). Example:

 

 

 

Press Ctrl+Alt+Del

 

 

 

 

Words in italics

Italics are used to:

 

 

 

Emphasize a point.

 

 

 

Denote a new term at the place where it is defined in the

 

 

 

text.

 

 

 

Identify menu names, menu commands, and software

 

 

 

button names. Examples:

 

 

 

From the Help menu, select Contents.

 

 

 

Click OK.

 

 

 

 

 

 

Feedback About

Your suggestions are very important to us. They will help make our

this User Guide

documentation more useful to you. Please e-mail comments about this

 

document to 3Com at:

pddtechpubs_comments@3com.com

Please include the following information when commenting:

Document title

Document part number (on the title page)

Page number (if appropriate)

Related Documentation

7

Example:

OfficeConnect ADSL Wireless 11g Firewall Router User Guide

Part Number DUA100A-72AAA01

Page 24

Do not use this e-mail address for technical support questions. For information about contacting Technical Support, please refer to Appendix E.

Related

In addition to this guide, each Router document set includes one

Documentation

Installation Guide. This guide contains the instructions you need to install

 

and configure your Router.

8 ABOUT THIS GUIDE

1

INTRODUCING THE ROUTER

 

 

Welcome to the world of networking with 3Com®. In the modern

 

business environment, communication and sharing information is crucial.

 

Computer networks have proved to be one of the fastest modes of

 

communication but, until recently, only large businesses could afford the

 

networking advantage.

 

 

OfficeConnect ADSL

The OfficeConnect ADSL Wireless 11g Firewall Router is designed to

Wireless 11g

provide a cost-effective means of sharing a single broadband Internet

Firewall Router

connection amongst several wired and wireless computers. The Router

 

also provides protection in the form of an electronic “firewall” preventing

 

anyone outside of your network from seeing your files or damaging your

 

computers. The Router can also prevent your users from accessing Web

 

sites which you find unsuitable.

 

Figure 1 shows an example network without a Router. In this network,

 

only one computer is connected to the Internet. This computer must

 

always be powered on for the other computers on the network to access

 

the Internet.

10 CHAPTER 1: INTRODUCING THE ROUTER

Figure 1 Example Network Without a Router

When you use the Router in your network (Figure 2), it becomes your connection to the Internet. Connections can be made directly to the Router, or to an OfficeConnect Switch or Hub, expanding the number of computers you can have in your network.

Figure 2 Example Network Using a Firewall Router

Router Advantages 11

Router Advantages The advantages of the Router include:

Shared Internet connection for both wired and wireless computers

High speed 802.11g wireless networking

No need for a dedicated, “always on” computer serving as your Internet connection

Cross-platform operation for compatibility with Windows, Unix and Macintosh computers

Easy-to-use, Web-based setup and configuration

Provides centralization of all network address settings (DHCP)

Acts as a Virtual server to enable remote access to Web, FTP, and other services on your network

Security — Firewall protection against Internet hacker attacks and encryption to protect wireless network traffic

Package Contents The Router kit includes the following items:

One OfficeConnect ADSL Wireless 11g Firewall Router

One power adapter for use with the Router

Four rubber feet

One Telephone Cable

One CD-ROM containing this User Guide

Installation Guide

One Support and Safety Information Sheet

One Warranty Flyer

If any of these items are missing or damaged, please contact your retailer.

12 CHAPTER 1: INTRODUCING THE ROUTER

Minimum System

and Component

Requirements

Your Router requires that the computer(s) and components in your network be configured with at least the following:

A computer with an operating system that supports TCP/IP networking protocols (for example Windows 98/NT/Me/2000/XP, Unix, Mac OS 8.5 or higher).

An Ethernet 10 Mbps or 10/100 Mbps NIC for each computer to be connected to the four-port switch on your Router.

An 802.11b or 802.11g wireless NIC.

An active ADSL subscription and connection.

A Web browser that supports JavaScript, such as Netscape 4.7 or higher, Internet Explorer 5.0 or higher, or Mozilla 1.2.1 or higher.

Front Panel

The front panel of the Router contains a series of indicator lights (LEDs)

 

that help describe the state of various networking and connection

 

operations.

 

Figure 3 Router - Front Panel

 

1

 

 

2

 

 

3

5

 

4

 

 

 

 

 

3CRWDR100A-72

 

LAN Status

 

Power SYNC OnlineWLAN

1

2

3

4

OfficeConnect ADSL Wireless 11g Firewall Router

Green = 100M, Yellow = 10M, Flash = Activity

1Power LED

Green

Indicates that the Router is powered on.

2SYNC LED

Green

If the LED is on it indicates that DSL connection is present. This LED flashes during configuration at power up.

Rear Panel 13

3Online LED

Green

If this LED is on, your username/password has been authenticated successfully with your ISP.

4Wireless LAN (WLAN) Status LED

Green

If the LED is on it indicates that wireless networking is enabled. If the LED is flashing, the link is OK and data is being transmitted or received. If the LED is off, the Wireless LAN has been disabled in the Router, or there is a problem. Refer to Chapter 6 “Troubleshooting”.

5LAN Status LEDs

Green

If the LED is on, the link between the port and the next piece of network equipment is OK. If the LED is flashing, the link is OK and data is being transmitted or received. If the LED is off, nothing is connected, or the connected device is switched off, or there is a problem with the connection (refer to Chapter 6 “Troubleshooting”). The port will automatically adjust to the correct speed and duplex.

Rear Panel

The rear panel (Figure 4) of the Router contains four LAN ports, one ADSL

 

port, a reset button, a power switch, and a power adapter socket.

 

Figure 4 Router - Rear Panel

6

7

8

9

10

11

 

 

12 VDC

 

 

 

 

 

 

 

1A MAX

 

 

 

 

 

 

 

 

ADSL

Power

Reset

LAN4

LAN3

LAN2

LAN1

6Wireless Antennae

The antennae on the product should be placed in a ‘V’ position when initially installed.

CAUTION: Do not force the antennae beyond their mechanical stops. Rotating the antennae further may cause damage.

14 CHAPTER 1: INTRODUCING THE ROUTER

7ADSL Port

Using the RJ11 cable provided, you should connect your Router to the telephone socket via a splitter.

8Power Adapter Socket

Only use the power adapter that is supplied with this Router. Do not use any other adapter.

9Reset Button

If you want to reset your Router to factory default settings, and cannot access the web management interface (for example, due to a lost password), then you may use this button. Refer to “Forgotten Password and Reset to Factory Defaults” on page 84 for further details.

10Power Switch

Push this switch to the “in” position to turn the unit on. In the “out” position, the unit is off.

11Ethernet Ports

Using suitable RJ45 cables, you can connect your Router to a computer, or to any other piece of equipment that has an Ethernet connection (for example, a hub or a switch). These ports have an automatic MDI/MDIX feature, which means either straight-through or a crossover cable can be used.

2

INSTALLING THE ROUTER

 

Introduction

This chapter will guide you through a basic installation of the Router,

 

including:

 

Connecting the Router to the Internet.

 

Connecting the Router to your network.

 

Setting up your computers for networking with the Router.

Safety Information

Please note the following:

 

WARNING: Please read the “Safety Information” section in Appendix C

 

before you start.

 

VORSICHT: Bitte lesen Sie den Abschnitt “Wichtige Sicherheitshinweise”

 

sorgfältig durch, bevor Sie das Gerät einschalten.

 

AVERTISSEMENT: Veuillez lire attentivement la section “Consignes

 

importantes de sécurité” avant de mettre en route.

Positioning the

Router

You should place the Router in a location that:

is conveniently located for connection to the telephone socket.

is centrally located to the wireless computers that will connect to the Router. A suitable location might be on top of a high shelf or similar furniture to optimize wireless connections to computers in both horizontal and vertical directions, allowing wider coverage.

allows convenient connection to the computers that will be connected to the four LAN ports on the rear panel, if desired.

allows easy viewing of the front panel LED indicator lights, and access to the rear panel connectors, if necessary.

16 CHAPTER 2: INSTALLING THE ROUTER

When positioning your Router, ensure:

It is out of direct sunlight and away from sources of heat.

Cabling is away from power lines, fluorescent lighting fixtures, and sources of electrical noise such as radios, transmitters and broadband amplifiers.

Water or moisture cannot enter the case of the unit.

Air flow around the unit and through the vents in the side of the case is not restricted. 3Com recommends you provide a minimum of

25 mm (1 in.) clearance.

Using the Rubber Use the four self-adhesive rubber feet to prevent your Router from Feet moving around on your desk or when stacking with flat top units. Only

stick the feet to the marked areas at each corner of the underside of your Router.

Powering Up the

 

To power up the Router:

Router

 

 

 

1

Plug the power adapter into the power adapter socket located on the

 

 

back panel of the Router.

 

2

Plug the power adapter into a standard electrical wall socket.

 

3

Press the power button located on the back of the Router.

 

 

 

Connecting the

 

The first step for installing your Router is to physically connect it to the

Router

 

telephone socket and then connect it to a computer in order to be able to

 

 

access the Internet. See Figure 5:

Connecting the Router

17

Figure 5 Connecting the Router

Internet

 

Power

 

Supply Unit

3Com OfficeConnect

 

Telephone

ADSL Wireless 11g Firewall Router

Socket

 

Splitter/

 

Microfilter Block

 

Your PC

Wireless

Users

1Run the provided telephone cable from the wall jack providing ADSL service to the ADSL port on your ADSL Router. When inserting an ADSL RJ-11 plug, be sure the tab on the plug clicks into position to ensure that it is properly seated. If you are using splitterless ADSL service, add low-pass filters between the ADSL wall jack and your telephones. (These filters pass voice signals through but filter data signals out.)

2Then:

If you are using a full-rate (G.dmt) connection, your service provider will attach the outside ADSL line to a data/voice splitter. In this case you can connect your phones and computer directly to the splitter as shown below (Figure 6):

or

If you are using a splitterless (G.lite) connection, then your service provider will attach the outside ADSL line directly to your phone system. In this case you can connect your phones and computer directly to the incoming ADSL line, but you will have to add low-pass

filters to your phones as shown below (Figure 7)

18 CHAPTER 2: INSTALLING THE ROUTER

Figure 6 Installing with a splitter

Connecting the Router

19

Figure 7 Installing without a splitter

You have now completed the hardware installation of your Router. Next you need to set up your computers so that they can make use of the Router to communicate with the Internet.

3Com recommends that you perform the initial Router configuration from a computer that is directly connected to one of the LAN ports.

If you configure the Router from a wireless computer, note that you may lose contact with the Router if you change the wireless configuration.

To communicate wirelessly with your Router, your wireless NIC should be set as follows:

Encryption — none

SSID — 3Com

Channel — 11

20 CHAPTER 2: INSTALLING THE ROUTER

3

SETTING UP YOUR COMPUTERS

 

The Router has the ability to dynamically allocate network addresses to the computers on your network, using DHCP. However, your computers need to be configured correctly for this to take place. To change the configuration of your computers to allow this, follow the instructions in this chapter.

Obtaining an IP

Address

Automatically

Windows 2000 If you are using a Windows 2000-based computer, use the following procedure to change your TCP/IP settings:

1From the Windows Start Menu, select Settings > Control Panel.

2Double click on Network and Dial-Up Connections.

3Double click on Local Area Connection.

4Click on Properties.

5A screen similar to Figure 8 should be displayed. Select Internet Protocol TCP/IP and click on Properties.

22 CHAPTER 3: SETTING UP YOUR COMPUTERS

Figure 8 Local Area Properties Screen

6Ensure that the options Obtain an IP Address automatically, and Obtain DNS server address automatically are both selected as shown in Figure 9. Click OK.

Figure 9 Internet Protocol (TCP/IP) Properties Screen

7 Restart your computer.

Obtaining an IP Address Automatically

23

Windows XP

1From the Windows Start menu, select Control Panel.

2Click on Network and Internet Connections.

3Click on the Network Connections icon.

4Double click on LAN or High Speed Connection icon. A screen titled Local Area Connection Status will appear.

5Select Internet Protocol TCP/IP and click on Properties.

6Ensure that the options Obtain an IP Address automatically, and Obtain DNS servers automatically are both selected. Click OK.

7Restart your computer.

Windows 98/ME

1From the Windows Start Menu, select Settings > Control Panel.

2Double click on Network. Select the TCP/IP item for your network card and click on Properties.

3In the TCP/IP dialog, select the IP Address tab, and ensure that Obtain IP address automatically is selected. Click OK.

Macintosh If you are using a Macintosh computer, use the following procedure to change your TCP/IP settings:

1From the desktop, select Apple Menu, Control Panels, and TCP/IP.

2In the TCP/IP control panel, set Connect Via: to Ethernet.

3In the TCP/IP control panel, set Configure: to Using DHCP Server.

4Close the TCP/IP dialog box, and save your changes.

5Restart your computer.

24 CHAPTER 3: SETTING UP YOUR COMPUTERS

Disabling PPPoE If you have PPPoE client software installed on your computer, you will and PPTP Client need to disable it. To do this:

Software

1From the Windows Start menu, select Settings > Control Panel.

2Double click on Internet Options.

3Select the Connections Tab. A screen similar to Figure 10 should be displayed.

4Select the Never Dial a Connection option.

Figure 10 Internet Properties Screen

 

You may want to remove the PPPoE client software from your computer

 

to free resources, as it is not required for use with the Router.

 

 

Disabling Web

Ensure that you do not have a web proxy enabled on your computer.

Proxy

 

Go to the Control Panel and click on Internet Options. Select the Connections tab and click LAN Settings at the bottom. Make sure that the Use Proxy Server option is unchecked.

4

RUNNING THE SETUP WIZARD

 

Accessing the Setup The Router setup program is Web-based, which means that it is accessed Wizard through your Web browser (Netscape Navigator 4.7 or higher, Internet

Explorer 5.0 or higher, or Mozilla 1.2.1 or higher).

To use the Setup Wizard:

1Ensure that you have at least one computer connected to the Router. Refer to Chapter 2 for details on how to do this.

2Launch your Web browser on the computer.

3Enter the following URL in the location or address field of your browser: http://192.168.1.1 (Figure 11). The Login screen displays.

Figure 11 Web Browser Location Field (Factory Default)

4To log in as an administrator, enter the password (the default password is admin) in the Password field and click Log in (Figure 12).

3COM WL-542 User Manual

26 CHAPTER 4: RUNNING THE SETUP WIZARD

Figure 12 Router Login Screen

5When you have logged in either:

The Status screen will appear (Figure 13). Select Setup Wizard from the menu.

or

If your Router has not been configured before, the Wizard will launch automatically (refer to Figure 14).

6You will be guided step by step through a basic setup procedure.

Figure 13 Status Screen

Accessing the Setup Wizard

27

Setup Wizard - Figure 14 Connection Type Screen

Connection Type

The Connection Type screen allows you to set up the Router for the type of Internet connection you have. Before setting up your connection type, have your account information from your ISP ready.

Select a DSL mode from the following:

PPPoE — PPP over Ethernet, providing routing for multiple PCs, see page 28

PPPoA — PPP over ATM, providing routing for multiple PCs, see page 29

Bridge Mode (for a single PC) — RFC1483 Bridged Mode, for single PCs only, see page 31

Routing Mode over ATM — RFC1483 Routed Mode, for multiple PCs, see page 32

Dynamic/Fixed IP in 1483 Bridge Mode (for multiple PCs), see page 33

and click Next.

For further information on selecting a mode see “Internet Settings” on page 46.

28 CHAPTER 4: RUNNING THE SETUP WIZARD

PPPoE Mode

Figure 15 PPPoE Screen

To set up the router for use with a PPP over Ethernet (PPPoE) connection, use the following procedure:

1Enter your PPP over Ethernet user name in the Username text box.

2Enter your PPP over Ethernet password in the Password text box.

3Re-type your PPP over Ethernet password in the Retype Password text box.

4Enter your VPI and VCI information in the VPI/VCI text boxes.

5Select the encapsulation type (LLC or VC MUX) in the Encapsulation drop-down list. This information will have been provided to you by your ISP.

6Check all of your settings, and then click Next. The Wireless Settings screen is displayed.

Loading...
+ 94 hidden pages