3COM 3C905C-TX, 3C905C-TX-M User Manual

5 (1)

EtherLink® 10/100 PCI for

CompletePCManagement

Network Interface Cards

User Guide

3C905C-TX and 3C905C-TX-M EtherLink 10/100 PCI NICs for Complete PC Management

http://www.3com.com/

http://www.3com.com/productreg

Part No. 09-1488-000

Published March 1999

3Com Corporation 5400 Bayfront Plaza Santa Clara, California 95052-8145

Copyright © 1999, 3Com Corporation. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without written permission from 3Com Corporation.

3Com Corporation reserves the right to revise this documentation and to make changes in content from time to time without obligation on the part of 3Com Corporation to provide notification of such revision or change.

3Com Corporation provides this documentation without warranty, term, or condition of any kind, either implied or expressed, including, but not limited to, the implied warranties, terms or conditions of merchantability, satisfactory quality, and fitness for a particular purpose. 3Com may make improvements or changes in the product(s) and/or the program(s) described in this documentation at any time.

If there is any software on removable media described in this documentation, it is furnished under a license agreement included with the product as a separate document, in the hard copy documentation, or on the removable media in a directory file named LICENSE.TXT or !LICENSE.TXT. If you are unable to locate a copy, please contact 3Com and a copy will be provided to you.

UNITED STATES GOVERNMENT LEGEND

If you are a United States government agency, then this documentation and the software described herein are provided to you subject to the following:

All technical data and computer software are commercial in nature and developed solely at private expense. Software is delivered as “Commercial Computer Software” as defined in DFARS 252.227-7014 (June 1995) or as a “commercial item” as defined in FAR 2.101(a) and as such is provided with only such rights as are provided in 3Com’s standard commercial license for the Software. Technical data is provided with limited rights only as provided in DFAR 252.227-7015 (Nov 1995) or FAR 52.227-14 (June 1987), whichever is applicable. You agree not to remove or deface any portion of any legend provided on any licensed program or documentation contained in, or delivered to you in conjunction with, this User Guide.

Unless otherwise indicated, 3Com registered trademarks are registered in the United States and may or may not be registered in other countries.

3Com, the 3Com logo, DynamicAccess, EtherDisk, EtherLink, and Parallel Tasking are registered trademarks of 3Com Corporation. Intelligent Auto Install is a trademark of 3Com Corporation. 3Com Facts is a service mark of 3Com Corporation.

Magic Packet is a trademark of Advanced Micro Devices, Inc. Wake on LAN is a trademark of International Business Machines Corporation. Microsoft, Windows, and Windows NT are trademarks of Microsoft Corp. Novell and NetWare are trademarks of Novell, Inc. SCO is a trademark of The Santa Cruz Operation, Inc.

All other company and product names may be trademarks of the respective companies with which they are associated.

CONTENTS

ABOUT THIS GUIDE

 

Conventions

9

 

 

 

 

 

 

 

Year 2000 Compliance

10

 

 

 

 

 

 

 

 

 

 

 

 

 

1 INTRODUCTION

 

 

 

 

 

 

 

3C905C NIC Overview

11

 

 

 

 

 

 

Features

12

 

 

 

 

 

 

 

Using Remote Wake-Up

12

 

 

 

 

 

Remote Wake-Up Requirements

13

 

 

 

Multiple NIC Installations and Remote Wake-Up

13

 

Using the Managed PC Boot Agent (MBA) Software

13

 

Using DynamicAccess Software

14

 

 

 

 

Using the Workgroup Keep-Alive Packet

15

 

 

Using Remote System Alerts 15

 

 

 

 

 

Remote System Alerts Requirements

15

 

 

Supported Remote System Alerts

15

 

 

 

Using Desktop Management Interface (DMI) 2.0 16

 

 

 

 

2 NETWORK INTERFACE CARD INSTALLATION

 

 

Overview

17

 

 

 

 

 

 

 

Preparing for Installation

18

 

 

 

 

 

 

Running the Preinstallation Program

19

 

 

 

 

Inserting the NIC 19

 

 

 

 

 

 

 

Connecting the Remote Wake-Up Cable

22

 

 

 

Connecting SOS or SMBus Cables for Remote System Alerts 24

 

Connecting to the Network

24

 

 

 

 

3WINDOWS 95/98 AND WINDOWS NT DRIVER INSTALLATION

Overview 27

 

 

 

Installing the Driver

27

 

Windows 95

27

 

 

Windows 98

30

 

 

Windows NT 4.0

32

 

Windows NT 3.51

33

 

Verifying Successful Installation

35

Windows 95 and Windows 98

35

Windows NT 4.0

35

 

Windows NT 3.51

36

 

Installing Multiple NICs

36

 

Windows 95 and Windows 98

36

Windows NT 4.0

37

 

4 NETWARE CLIENT AND SERVER DRIVER INSTALLATION

 

Installing the NetWare Client Driver

39

 

 

 

About 3Com Intelligent Auto Install Software

39

 

Intelligent Auto Install Requirements

40

 

 

Running the Intelligent Auto Install Program

40

 

Installing the NetWare Server Driver

41

 

 

 

Obtaining NetWare Loadable Modules

41

 

 

NetWare 3.12

41

 

 

 

 

 

NetWare 4.10 and 4.11

42

 

 

 

 

Multiple NICs

42

 

 

 

 

 

Verifying the PCI Slot Number

43

 

 

 

 

 

 

 

 

5 NIC CONFIGURATION

 

 

 

 

 

Configuration Methods 45

 

 

 

 

 

Default NIC Settings

46

 

 

 

 

 

Changing General NIC Configuration Settings

47

 

Configuring the Managed PC Boot Agent (MBA)

49

 

Enabling or Disabling the Boot ROM Setting

49

 

Booting From the Network

50

 

 

 

 

BBS BIOS-Compatible PCs

50

 

 

 

Non-BBS BIOS-Compatible PCs 51

 

6 TROUBLESHOOTING AND DIAGNOSTICS

 

Troubleshooting the Installation 53

 

 

Accessing 3Com Support Databases

54

 

 

Accessing the 3Com Knowledgebase

54

 

Accessing the 3Com NIC Help System

54

 

Accessing Release Notes and Frequently Asked

 

Questions 55

 

 

 

 

 

 

Interpreting the LEDs

56

 

 

 

 

Running the NIC Diagnostics Tests

57

 

 

To Run the Network Test

58

 

 

 

To Run the NIC Test

 

59

 

 

 

 

To Run the Remote Wake-Up Test 59

 

 

Troubleshooting Remote Wake-Up

61

 

 

Viewing Network Statistics

62

 

 

 

Using the 3Com Icon in the Windows System Tray 63

 

Removing NIC Software

64

 

 

 

 

Windows 95 and Windows 98

64

 

 

Windows NT 4.0

64

 

 

 

 

Windows NT 3.51

 

65

 

 

 

 

Frequently Asked Questions

66

 

 

 

 

A SPECIFICATIONS AND CABLING REQUIREMENTS

 

Hardware Specifications

69

 

 

 

 

Network Interface

 

69

 

 

 

 

Physical Dimensions

 

69

 

 

 

 

Environmental Operating Range

69

 

 

Power Requirements

69

 

 

 

Standards Conformance

70

 

 

 

Cabling Requirements

 

70

 

 

 

 

Twisted-Pair Cable

 

70

 

 

 

 

10BASE-T Operation

71

 

 

 

100BASE-TX Operation

72

 

 

 

RJ-45 Connector Pin Assignments

72

 

B DYNAMICAccess SOFTWARE INSTALLATION

AND CONFIGURATION

 

Client PC Requirements

73

 

 

Installing DynamicAccess Software

74

 

Verifying Successful Installation 75

 

 

Configuring DynamicAccess Software

75

 

Removing DynamicAccess Software

76

 

 

C 3COM DMI AGENT INSTALLATION

 

Overview 77

 

 

 

System Requirements

78

 

Client PC Requirements 78

Network Management Requirements 78

Installing the 3Com DMI Agent 79

D TECHNICAL SUPPORT

Support from Your Network Supplier

81

Online Technical Services

81

 

 

World Wide Web Site

81

 

 

3Com FTP Site 82

 

 

 

3Com Bulletin Board Service

82

 

Access by Analog Modem

82

 

Access by Digital Modem

83

 

3Com Facts Automated Fax Service

83

INDEX

3COM CORPORATION LIMITED WARRANTY

FCC CLASS B STATEMENT

FCC DECLARATION OF CONFORMITY

3COM END USER SOFTWARE LICENSE AGREEMENT

FIGURES

1

3C905C Network Interface Cards

11

2

Installing the NIC

21

 

 

3

Connecting the Remote Wake-Up Cable 23

4

Connecting to the RJ-45 Port

25

 

5

Add New Hardware Wizard

30

 

6

Network Settings Window

34

 

7

Selected NIC Screen

44

 

 

8

General Screen

48

 

 

 

9

Configuration Screen

48

 

 

10

Support Screen

55

 

 

 

11

Diagnostics Screen

58

 

 

12

Remote Wake-Up Test Screen

60

 

13

Statistics Screen

62

 

 

 

14

RJ-45 Connector Pin Assignments

72

15DynamicAccess Software Setup Screen — Traffic Prioritization 76

TABLES

1

Notice Icons

9

 

 

 

2

Text Conventions

10

 

 

3

Installation Overview

17

 

 

4

Cable Specifications

24

 

 

5

NetWare NLMs

41

 

 

6

NIC Configuration Methods

45

 

7

NIC Configuration Settings

46

 

8

Installation Troubleshooting Tips

53

9

LED Interpretations

56

 

 

10

Frequently Asked Questions

66

 

11

Unshielded Twisted-pair Cable Categories 71

12

DynamicAccess Software Minimum Client Requirements 74

ABOUT THIS GUIDE

This guide describes how to install, configure, and troubleshoot the 3Com® EtherLink® 10/100 PCI for Complete PC Management (3C905C) network interface card (NIC).

This guide is intended for those who install and configure Ethernet NICs. Some familiarity with Ethernet networks and NICs is assumed.

If release notes are shipped with your product and the information there differs from the information in this guide, follow the instructions in the release notes.

Most user guides and release notes are available in Adobe Acrobat Reader Portable Document Format (PDF) or HTML on the 3Com World Wide Web site:

http://www.3com.com/

You can download Acrobat Reader from the Adobe

Systems Incorporated Web site:

http://www.adobe.com/

Conventions

Table 1 and Table 2 list conventions that are used throughout this guide.

Table 1 Notice Icons

 

Icon

 

 

Notice Type

Description

 

 

 

 

 

 

 

 

 

 

Information note

Information that describes important features

 

 

 

 

 

or instructions

 

 

 

 

 

 

 

 

 

 

Caution

Information that alerts you to potential loss of

 

 

 

 

 

 

 

 

 

 

data or potential damage to an application,

 

 

 

 

 

system, or device

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Warning

Information that alerts you to potential

 

 

 

 

 

 

 

 

 

personal injury

 

 

 

 

 

 

10 ABOUT THIS GUIDE

Table 2 Text Conventions

Convention

Description

 

 

Screen displays

This typeface represents information as it appears on

 

the screen.

 

 

Commands

The word “command” means that you must enter the

 

command exactly as shown and then press Return or

 

Enter. Commands appear in bold. Example:

 

To launch the DOS diagnostics program, enter the

 

following command:

 

 

a: install

 

 

The words “enter”

When you see the word “enter” in this guide, you

and “type”

must type something, and then press Return or Enter.

 

Do not press Return or Enter when an instruction simply

 

says “type.”

 

 

Words in italics

Italics are used to:

 

Emphasize a point.

 

Denote a new term at the place where it is defined in

 

 

the text.

 

Identify menu names, menu commands, and software

button names. Examples:

From the Help menu, select Contents.

Click OK.

Year 2000 Compliance

For information on Year 2000 compliance and 3Com products, visit the 3Com Year 2000 Web page:

http://www.3com.com/products/yr2000.html

1 INTRODUCTION

This chapter describes the 3Com® EtherLink® 10/100 PCI for Complete PC Management (3C905C) network interface card (NIC).

3C905C NIC Overview

RJ-45 port

LEDs

The 3C905C NIC is a 10/100 Mbps PCI NIC that includes a suite of desktop management features, including Remote Wake-Up, managed PC boot agent, system alerts, workgroup keep-alive, and DMI 2.0 support.

The two versions of the 3C905C NIC are shown in Figure 1 and described in the next section.

Figure 1 3C905C Network Interface Cards

MBA

Boot ROM

Boot ROM

socket

SOS pin connector

System Management

Bus (SMB) connector

Remote Wake-Up (RWU) connector

TX

DATA

TX

DATA

 

 

ACT

 

ACT

 

10

L

10

L

100

N

100

N

K

K

3C905C-TX-M 3C905C-TX

12 CHAPTER 1: INTRODUCTION

Features

The 3C905C NIC supports the following features:

Remote Wake-Up

Managed PC Boot Agent (MBA) software (integrated as a boot ROM on the 3C905C-TX-M NIC; available separately for installation and use with the 3C905C-TX NIC)

DynamicAccess® software

Remote system alerts

Workgroup keep-alive packet

Desktop Management Interface (DMI) 2.0 and 2.0s

PCI 2.2

Wired for Management 2.0

Advanced Configuration Power Interface (ACPI)

Parallel Tasking® and Parallel Tasking II technology

802.3x Flow Control

TCP/IP Checksum

For a complete list of the standards that the 3C905C NIC supports, see “Standards Conformance” in Appendix A.

Unless specifically indicated, 3C905C is used throughout this guide to refer to both NICs.

Using Remote Wake-Up

Remote Wake-Up is the ability to remotely power-on a PC for after-hours administration.

Remote Wake-Up support is enabled in one of two ways:

If your PC is compliant with PCI 2.2, Remote Wake-Up is automatically enabled through the PCI bus. No special installation is required. (See your PC documentation if you are unsure whether your PC is compliant with

PCI 2.2.)

If your PC is not compliant with PCI 2.2, you must connect a Remote Wake-Up cable from the NIC Remote Wake-Up (RWU) connector (see Figure 1) to a 3-pin Remote Wake-Up connector on the PC

motherboard. See “Connecting the Remote Wake-Up Cable” in Chapter 2 for instructions.

3C905C NIC Overview

13

Remote Wake-Up Requirements

Your PC or server must have the following items to use Remote Wake-Up:

BIOS that supports Remote Wake-Up

PCI 2.2-compliant bus or a 3-pin Remote Wake-Up connector on the PC motherboard and a 5-volt standby power supply unit rated at a minimum of

375 milliamperes

If you are unsure whether your PC meets the requirements listed above, refer to your PC documentation or contact your PC manufacturer.

For more information on Remote Wake-Up, including a list of PCs that currently support this feature, go to the following 3Com World Wide Web site:

http://www.3com.com/partners/acpi

Multiple NIC Installations and Remote Wake-Up

To use multiple NICs as Remote Wake-Up NICs in the same PC, the PC must have a power supply that can support multiple Remote Wake-Up devices.

See your PC documentation if you are unsure whether your PC power supply can accommodate more than one Remote Wake-Up device.

Using the Managed PC Boot Agent (MBA) Software

The 3C905C-TX-M NIC has an installed boot ROM (see Figure 1) that contains Managed PC Boot Agent (MBA) software.

A boot ROM with MBA software can be purchased separately for installation and use with the 3C905C-TX NIC.

The MBA adds management capabilities to the NIC by enabling the PC to boot from the server, rather than from its local drive.

This preboot support allows you to use management applications to remotely:

Install and configure a new PC that has never been connected to the network.

Upgrade software.

14CHAPTER 1: INTRODUCTION

Configure or reconfigure multiple systems simultaneously.

Scan for viruses.

Back-up hard drives and perform disaster recovery tasks.

For information on configuring the MBA to boot from the network, see “Configuring the Managed PC Boot Agent (MBA)” in Chapter 5.

For detailed information on the MBA, see the

Managed PC Boot Agent User Guide, located on the MBA Utility diskette.

Using DynamicAccess Software

The 3C905C NIC comes with DynamicAccess software, advanced network software that improves performance, management, and control of your network.

DynamicAccess software adds intelligence to the NIC by integrating the following features:

Distributed RMON (dRMON) SmartAgents — Enables full RMON reporting on all network segments, including switched networks, without the need to place dedicated RMON probes throughout the network.

Traffic prioritization (IEEE 802.1p/Q) — Ensures that business-critical and delay-sensitive traffic (such as multimedia applications) has priority over normal data.

Fast IP—Eliminates router bottlenecks and improves performance in switched networks.

Efficient multicast control — Prevents flooding of switched networks by multicast applications such as video training, stock quotes, or online news.

DynamicAccess software can be installed on a PC running Windows 95, Windows 98, or Windows NT. See Appendix B for more information.

For detailed information on DynamicAccess software, go to the following 3Com World Wide Web site:

http://www.3com.com/dynamicaccess

3C905C NIC Overview

15

Using the Workgroup Keep-Alive Packet

The 3C905C NIC can transmit a workgroup keep-alive packet periodically while the PC is in a sleep state. This packet prevents the PCs workstation address from being aged-out of switch and router tables.

For instructions on enabling or disabling the workgroup keep-alive packet, see “Configuring the Workgroup Keep-Alive Packet” in Appendix D.

Using Remote System Alerts

The 3C905C NIC can be configured to continuously monitor the PC and transmit a remote system alert to an alert target management station when a specific event, such as a power problem or a case intrusion, is detected.

Remote System Alerts Requirements

To generate remote system alerts:

The 3C905C NIC must be connected to the PC motherboard using the NIC SOS or SMBus (SMB) connector.

See your PC documentation or contact your PC manufacturer if you are unsure whether the NIC can be connected (or already is connected) to the PC motherboard using one of these connectors.

The alert target management station that is to receive the alerts must have software that supports the Platform Event Trap Format (PETF) specification for remote system alerts.

See your management station software documentation if you are unsure whether it supports the PETF specification, the packet format used by the

3C905C NIC.

Supported Remote System Alerts

A PC can support a maximum of seven remote system alerts. The remote system alerts that are supported by your PC depend upon your PCs configuration.

16 CHAPTER 1: INTRODUCTION

Using Desktop Management Interface (DMI) 2.0

The 3C905C NIC supports DMI 2.0 and 2.0s, which enables managed PCs and net PCs to report details about themselves and their peripheral devices across the network to a DMI 2.0-compliant management application.

A network administrator can then use this information to configure and manage a client or server PC remotely.

For instructions on installing the 3Com DMI Agent, see Appendix C.

For more detailed information on DMI, go to the following 3Com World Wide Web site:

http://www.3com.com/managedpc

NETWORK INTERFACE CARD

2 INSTALLATION

This chapter describes how to install the 3C905C NIC in your PC and connect it to an Ethernet or Fast Ethernet network.

CAUTION: Do NOT physically install the NIC in your PC until you have run the preinstallation program, as described in “Running the Preinstallation Program” later in this chapter.

Overview

Table 3 provides an overview of how to install the 3C905C NIC, depending on your PC configuration.

Table 3 Installation Overview

Installation Task

Instructions

 

 

Installing the NIC in

To install the 3C905C NIC in a new PC or in a PC that

a new PC

never has had a NIC installed:

 

1

Run the NIC preinstallation program before installing

 

 

the NIC in the PC, as described in this chapter.

 

2

Install the NIC in the PC and connect it to the network,

 

 

as described in this chapter.

 

3

Install the NIC driver and software. See Chapter 3 or

 

 

Chapter 4 for instructions.

 

 

Installing multiple NICs

To install multiple 3C905C NICs in a Windows 95/98 or

 

Windows NT 4.0 PC, follow the instructions in “Installing

 

Multiple NICs” in Chapter 3.

 

To install multiple 3C905C NICs in a NetWare server,

 

follow the instructions in “Multiple NICs” in Chapter 4.

 

 

Replacing an

To install the 3C905C NIC in a PC in which a NIC has

installed NIC

previously been installed:

 

1

Remove the drivers and the NIC before installing the

 

 

3C905C NIC in the PC. See “Removing NIC Software”

 

 

in Chapter 6 for instructions.

 

2

Install the 3C905C NIC in the PC, following the

 

 

instructions in “Installing the NIC in a new PC” earlier

 

 

in this table.

(continued)

18 CHAPTER 2: NETWORK INTERFACE CARD INSTALLATION

Table 3 Installation Overview (continued)

Upgrading Windows 95 To upgrade a PC from Windows 95 to Windows 98 in to Windows 98 which a 3C90x NIC has already been installed, follow the

instructions in the WIN98.TXT file located in the HELP directory on EtherDisk diskette 3.

Updating EtherDisk To update EtherDisk 4.x or earlier software to EtherDisk 5.x software software, follow the instructions in the text file appropriate

for your operating system in the HELP directory on EtherDisk diskette 3.

Preparing for Installation

Before you install the NIC in your PC, make sure that you have the following items:

3C905C NIC

3Com EtherDisk diskettes 1, 2, and 3

Remote Wake-Up cable (This cable is optional. Install it only if you want to use Remote Wake-Up and your PC is not compliant with PCI 2.2. Contact your PC manufacturer for the Remote Wake-Up cable.)

SOS or SMBus cable (This cable is optional. Install it only if you want to use remote system alerts and your PC has a matching connector on its motherboard. Contact your PC manufacturer for cabling and installation instructions.)

If the 3C905C NIC or the EtherDisk diskettes are damaged or missing, contact your shipper or network supplier.

You also need to know the following about your network environment:

The kind of network cabling that is used to connect to the network at your site (10BASE-T or 100BASE-TX).

Your network protocol (IPX, NetBEUI, or TCP/IP).

Running the Preinstallation Program

19

Running the Preinstallation Program

Before you physically install the NIC in your PC, you must run the following preinstallation program to properly set up your system environment.

CAUTION: If you do not run the preinstallation program, the NIC driver and software will not be installed correctly.

To run the preinstallation program:

1Do not install the NIC in the PC.

2Turn on the power to the PC and start Windows.

3Insert EtherDisk diskette 1 in drive A.

4From the Windows Start menu, select Run.

5Run the preinstallation program. Enter: a:\preinstl

6After the preinstallation program finishes, turn off the power to the PC and remove EtherDisk diskette 1.

The next step is to install the NIC in the PC.

Inserting the NIC

The following instructions apply to installing the NIC in most PCs. If these instructions are not appropriate for your PC, refer to the documentation that accompanied your PC.

CAUTION: Do NOT install the NIC in your PC until you have run the preinstallation program, as described in the previous section, “Running the Preinstallation Program.”

Before handling the NIC, touch the bare metal case of your PC to discharge static electricity from your body. While you are handling the NIC, wear a wrist strap grounded to the PC chassis.

20 CHAPTER 2: NETWORK INTERFACE CARD INSTALLATION

To install the NIC in your PC:

1Make sure that you have run the preinstallation program, as described in the previous section.

2Remove all jewelry from your hands and wrists. Use only insulated or nonconducting tools.

3Make sure that the power to the PC is turned off and that the power cord is unplugged.

4Remove the cover from your PC.

5Locate an empty, nonshared bus mastering PCI slot and remove the corresponding slot cover. Save the screw.

Do not install the NIC in a shared PCI slot. Avoid any

PCI slot next to an ISA slot. This is often a shared slot and does not support bus mastering.

If you do not know how to identify a PCI slot, check your PC documentation or ask your system administrator.

If you are planning to install the Remote Wake-Up cable or a cable for the SOS or SMBus connector, choose an empty PCI slot that is close to the matching connector on the

PC motherboard.

6Carefully insert the NIC into the empty PCI slot (see Figure 2). Press firmly to ensure that the NIC is fully seated in the slot.

Inserting the NIC

21

Figure 2 Installing the NIC

1 Remove slot cover

2 Insert NIC

PCI slots

7Secure the NIC with the screw you removed in step 5.

If you want to install the Remote Wake-Up cable, go to the next section, “Connecting the Remote Wake-Up Cable” to continue the installation. If you want to connect a cable from the SOS or SMBus connector, see your PC documentation or contact your PC manufacturer for instructions.

If you do not want to connect a cable, continue with step 8.

8Replace the PC cover and plug in the power cord.

Do not turn on the power to the PC.

9Go to “Connecting to the Network” later in this chapter.

22 CHAPTER 2: NETWORK INTERFACE CARD INSTALLATION

Connecting the Remote Wake-Up Cable

This section describes how to connect the Remote Wake-Up cable from the NIC to the PC motherboard.

Contact your PC manufacturer for the Remote

Wake-Up cable.

Connecting the Remote Wake-Up cable is optional. Connect this cable only if you want to use this feature and your PC has the following items:

3-pin Remote Wake-Up connector on the PC motherboard

5-volt standby power supply unit rated at a minimum of 375 milliamperes

BIOS that supports Remote Wake-Up

If your PC is compliant with PCI 2.2, Remote Wake-Up is automatically enabled through the PCI bus. You do not need to connect the Remote Wake-Up cable.

WARNING: Make sure that the PC power cord is unplugged. Only properly trained and authorized personnel should perform service. Contact your PC manufacturer for information about safe service techniques.

To connect the Remote Wake-Up cable:

1Make sure that the NIC is properly installed in a PCI slot.

2Insert the Remote Wake-Up cable into the RWU connector on the NIC (see Figure 3).

Twist the cable twice before attaching the cable to the PC.

3Attach the other end of the cable to the connector on the PC motherboard (see Figure 3).

Refer to your PC documentation if you need help locating the connector.

3COM 3C905C-TX, 3C905C-TX-M User Manual

Connecting the Remote Wake-Up Cable

23

Figure 3 Connecting the Remote Wake-Up Cable

Power supply

Connect Remote Wake-Up cable from NIC to motherboard connector

Plug in Remote Wake-Up cable to RWU connector

4Replace the PC cover and plug in the power cord.

Do not turn on the power to the PC.

5Go to the next section, “Connecting SOS or SMBus Cables for Remote System Alerts” or go directly to the following section, “Connecting to the Network.”

24 CHAPTER 2: NETWORK INTERFACE CARD INSTALLATION

Connecting SOS or SMBus Cables for Remote System Alerts

Connecting the SOS or SMBus cables is optional, and requires a matching connector on your PC motherboard. Connect one of these cables only if you want to use Remote System Alerts and if your PC supports this feature.

Contact your PC manufacturer for these cables.

To connect the SOS or SMBus cable for Remote System Alerts, confirm that your PC supports one of these cables and follow the instructions provided with the PC documentation.

Connecting to the Network

This section describes how to connect the 3C905C NIC RJ-45 port to an Ethernet or Fast Ethernet network.

The RJ-45 port provides a 10 Mbps or 100 Mbps connection automatically, depending on the speed of the connected hub or switch.

Table 4 shows the cable requirements and maximum network cable lengths for the 3C905C NIC.

Table 4 Cable Specifications

Network

Cable Required

Maximum

Environment

Cable Length

 

 

 

10 Mbps

Category 3, 4, or 5

100 m (328 ft)

(10BASE-T)

unshielded twisted-pair

 

 

 

 

100 Mbps

Category 5 unshielded

100 m (328 ft)

(100BASE-TX)

twisted-pair

 

 

 

 

Connecting to the Network

25

To connect the 3C905C NIC to a 10 Mbps Ethernet or 100 Mbps Fast Ethernet network:

1Plug the RJ-45 connector on the twisted-pair network cable into the RJ-45 port on the NIC backplate (see Figure 4).

Figure 4 Connecting to the RJ-45 Port

TX Data

ACT

10

L

N

100

K

 

RJ-45 connector

2Connect the other end of the network cable to an active network port.

The next step is to install the NIC driver and software.

Go to the appropriate chapter for your operating system.

3

WINDOWS 95/98 AND

WINDOWS NT

DRIVER INSTALLATION

This chapter describes how to install the NIC driver and software on a PC running Windows 95, Windows 98, Windows NT 4.0, or Windows NT 3.51.

To obtain the latest shipping version of a driver, contact your PC manufacturer.

Overview

You install the NIC driver and software using the EtherDisk diskettes after you have run the preinstallation program and installed the NIC in your PC, as described in Chapter 2.

The NIC driver can be used in both Microsoft and NetWare network environments.

Do not use the 3Com Intelligent Auto Install software to install the NIC driver under Windows 95, Windows 98, or Windows NT. The Intelligent Auto Install software

is for Windows 3.x and DOS clients connecting to a NetWare server. See Chapter 4 for more information.

Installing the Driver

To install the NIC driver and software, follow the steps in the section appropriate for your operating system.

Windows 95

If you encounter problems during the installation, see the W95NDIS.TXT file located in the HELP directory on EtherDisk diskette 3 for troubleshooting tips.

Before installing the NIC driver and software:

Make sure that you have run the preinstallation program, as described in Chapter 2.

Make sure that the NIC is installed in the PC and that it is connected to the network.

28 CHAPTER 3: WINDOWS 95/98 AND WINDOWS NT DRIVER INSTALLATION

Make sure that you have the Windows 95 installation files. These files may be on a CD or diskettes, or they may have been copied to your hard drive when Windows 95 was installed on your PC.

To install the NIC driver and software on a PC running Windows 95:

1Turn on the power to the PC.

Windows 95 detects the NIC.

Depending on the version of Windows 95 that you have installed, the New Hardware Found dialog box appears or the Update Device Driver Wizard starts.

If the New Hardware Found dialog box appears:

a Select Driver from disk provided by hardware manufacturer, and then click OK.

b Insert EtherDisk diskette 1 in drive A, make sure that A:\ appears in the entry box, and then click OK.

c Go to step 2 when prompted for EtherDisk diskette 2.

If the Update Device Driver Wizard starts:

aInsert EtherDisk diskette 1 in drive A, and then click Next.

Windows finds the driver and asks if you want to use this driver.

bClick Finish, and then click OK when prompted for EtherDisk diskette 1.

cGo to step 2 when prompted for EtherDisk diskette 2.

2Remove EtherDisk diskette 1 from drive A, insert EtherDisk diskette 2, and then click OK.

Files are copied.

If this is the first time that networking is being installed on your PC, the Identification tab of the Network screen appears. Go to step 3.

If networking has already been installed, you are prompted for the Windows 95 CD. Go to step 4.

Installing the Driver

29

3In the specified fields of the Identification tab screen, enter the following information, and then click OK:

Computer Name — Identifies the PC on the network for other users. This entry must be a unique name of 15 characters or fewer, containing no spaces.

Workgroup — Identifies the group (for example, your department name) to which your PC belongs. If you belong to a peer-to-peer network, this entry must be exactly the same for all the PCs in your network.

Computer Description — Displays additional details to other users on the network about this PC. For example, you could specify that the PC has a printer attached. Filling in this field is optional.

4Insert the Windows 95 CD or diskette, and then click OK.

If you do not have the Windows 95 CD or diskette, but the Windows 95 installation files are on your hard drive, click

OK. Enter the directory in the Copy Files From entry box (usually C:\WINDOWS\OPTIONS\CABS), and then click OK.

Files are copied. You are prompted for EtherDisk diskette 2.

5Make sure that EtherDisk diskette 2 is in drive A, and then click OK.

Files are copied. You are prompted to restart the PC.

6Remove EtherDisk diskette 2 from drive A, and then click Yes to restart the PC.

You must restart the PC to complete the installation.

The installation is complete. Go to “Verifying Successful Installation” later in this chapter to confirm that the NIC is properly installed.

After Windows restarts, double-click the Network icon in the Windows Control Panel and make sure that the configuration settings are properly set for your network environment. Contact your system administrator

for assistance.

Loading...
+ 67 hidden pages